Jon Ettman's Discussions (75)

Discussions Replied To (50) Replies Latest Activity

"The right arm."

Jon Ettman replied Jan 26 to 1964 Cadillac wiper syncronization

2 Jan 26
Reply by Jon Ettman

"Brian, I do have 2 buckets for a 1964 deVille. Contact Jon 5613010659"

Jon Ettman replied Jan 11 to 63 deville

3 Jan 11
Reply by Jon Ettman

"I do own a 1964 Deville convertable with factory bucket seats. It does have ac. Not…"

Jon Ettman replied Jan 11 to 64 CONVERTIBLE

5 Feb 28
Reply by Darien Sofie

"I have several side moldings for a 1964 Deville. Not sure if they are compatible. Jon"

Jon Ettman replied Jan 11 to Side molding for a 63 coupe.

7 Jun 8
Reply by Matti Roth

"Call Pro Fit. Her name is Libby. 256 8357107. She did the seats for my 64 Deville Co…"

Jon Ettman replied Mar 30, 2020 to bucket seat covers

3 Mar 31, 2020
Reply by Bobby Brown

"$10 and you pay the shipping. I will send pictures upon request. Thanks Jon"

Jon Ettman replied Aug 20, 2019 to Help! I need a 1964 Eldorado front left fender.

5 Aug 20, 2019
Reply by Jon Ettman

"I have a front left fender from my 1964 DeVille Convertable. The vehicle I bought ca…"

Jon Ettman replied Aug 20, 2019 to Help! I need a 1964 Eldorado front left fender.

5 Aug 20, 2019
Reply by Jon Ettman

"I have a front left fender from my 1964 DeVille Convertable. The vehicle I bought ca…"

Jon Ettman replied Aug 20, 2019 to Help! I need a 1964 Eldorado front left fender.

5 Aug 20, 2019
Reply by Jon Ettman

"What do the dash pad clips look like. Thanks Jon"

Jon Ettman replied Apr 25, 2019 to Wanted: retaining clips for dash pad legs

4 Apr 26, 2019
Reply by Russ Austin

"I do have several speakers only. If they would help you..."

Jon Ettman replied Jul 28, 2018 to Rear center speaker 63 Caddy Convertible

2 Jul 28, 2018
Reply by Jon Ettman

RSS

Photos

  • Add Photos
  • View All

Forum

Neutral Switch issues

Started by Rob Shatsnider in Restoration Discussion. Last reply by Mark S Anderson 8 minutes ago. 1 Reply

On a 1964 60 Special with a tilt wheel, tubro trans and #653 neutral switch.  When I had the transmission done the switch got out of alignment.  Now the car will start in Park, but not in Neutral,…Continue

Tags: issues, Switch, Neutral

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 33 minutes ago. 9 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 19 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

Carpet install

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 1 Reply

simple question, Does the carpet go under the seat mounts and bolted down with the seat? My original carpet was cut to go around the seat mounts looks like a hack job. Same with the steering column,…Continue

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service