Tom Bahner's Discussions (47)

Discussions Replied To (31) Replies Latest Activity

"Thanks all for the comments. Its kind of what I suspected.  Tom B"

Tom Bahner replied Sep 17 to Leaky Windshield

4 Sep 17
Reply by Tom Bahner

"Could this be a torus check valve problem? after sitting a couple days I end up with…"

Tom Bahner replied Aug 6 to Sealing up oil leaks

2 Aug 6
Reply by Tom Bahner

"Thanks for all the info. I feel a little more confident in getting some decent resul…"

Tom Bahner replied Jun 5 to Oil Leaks

8 Jun 5
Reply by Tom Bahner

"Thanks all. Not so concerned about valve covers and will pass along info on pan and…"

Tom Bahner replied Jun 3 to Oil Leaks

8 Jun 5
Reply by Tom Bahner

"Thanks all. I've been in everything on this seat. Motors, rails, relay, switch, etc.…"

Tom Bahner replied May 17, 2020 to 63 6 way Seat switch

4 May 17, 2020
Reply by Jason Edge

"I've had my '63 for 5 years now. Not afraid to drive it anywhere. Never been rebuilt…"

Tom Bahner replied Jul 29, 2019 to hypothetical

11 Jul 31, 2019
Reply by Jason Edge

"I have a couple. Message me for details. "

Tom Bahner replied May 11, 2019 to Intake mainfold

2 May 11, 2019
Reply by Christian Doerk

"That New Yorker is good property! It would have the flathead straight 8 instead of t…"

Tom Bahner replied Sep 24, 2018 to Hot Car Show

5 Sep 24, 2018
Reply by Ronnie Lay

"That's got to be a good feeling! Sounds like you'll have plenty of room for STUFF! W…"

Tom Bahner replied Sep 24, 2018 to We've done it..... but never again.

7 Oct 1, 2018
Reply by Kevin Campbell

"In May the wife and I took a 2600 km trip down a section of Rt 66. Ol Blue cruised d…"

Tom Bahner replied Sep 8, 2018 to Long road trip with '63 Cadillac

12 Sep 8, 2018
Reply by Tony and Ginny 429



  • Add Photos
  • View All


Whoa there, you want how much??

Started by Robert Gonzalez in 1963/64 Cadillac Specific Discussion 16 hours ago. 0 Replies

Ok, I’ve been on here for almost a decade. I KNOW we covet our cars and have always tried selling them at premium prices. But the bottom line, our cars rarely fetched prices over a covair. The…Continue

1964 Cadillac parts for sale... northern cali

Started by Jason in For Sale. Last reply by Jeremy yesterday. 1 Reply

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue

Tags: Parts

63 4 door Cadillac

Started by Walt Timmerman in For Sale. Last reply by Jeremy yesterday. 7 Replies

Need to start parting this car out. Might be moving soon and if its not parted out, it'll be scrapped.Also have Motor and transmission from my 63 coupe deville for sale. will part out also.Was told…Continue

Free- 64 lower bumper bucket - Passenger side

Started by Michael Buonaccorso in For Sale. Last reply by Jeremy yesterday. 1 Reply

This is in rough shape. Not only is there rust in the usual places but it is also bent. I replaced this piece on my car after an accident, but since this is a hard to come by piece, I figured someone…Continue

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…


1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…


New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …


Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…



  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service