To my knowledge, engine, transmission, and drive shaft are original to the car.
I am worried I am falling down the rabbit hole of vibrations.
Some tests I’ve done recently:
Going down flat and level good blacktop about 65/70, fairly noticeable vibration. Shift to N, vibration is significantly lessened.
When revving engine in P or N, there is fairly noticeable vibration.
Where should I start first? I know the rear portion of the drive shaft is often to blame and I am worried that is the case in my situation. But that seems like a hefty job I am unsure I can complete myself.
Ive also seen mention several times of the harmonic balancer. Again, not sure that’s something I can complete myself.
I am not opposed to have work done on those two areas, but finding someone in my area (Bloomington IL) to do the work is going to be a hurdle.
So, what are your thoughts on the issue?
1964 Fleetwood
Thanks!
Logan
Tags:
As always, I appreciate your experience!
I think getting as many new rubber parts as I can seems like a good place to start.
Having the engine and trans out are in my 5 year plan, so any internals will wait until then, but engine mounts and trans mounts seem like a fairly reasonable repair to see how that would fix the issue.
Are there any good ways to diag perhaps the rear portion of the drive shaft or maybe the center support bearing? Those also seem like reasonable repairs.
At the end of the day-the vibration is really not that dramatic. I feel a bit like Clovis, I’m sure my passengers would not notice the vibration, but I do HAHA and my ADHD is running rampant. And I am chasing things that aren’t a severe issue. realistically, the vibrations only start to get worse at 75/80+ which I NEVER run that fast regularly. Putting around at 45-65 is like a dream and that seems good enough for me.
I absolutely plan on keeping my car for the remainder of my life. But safety and driveability come first at this moment in my life.
If I had endless resources, I’d have the car fixed up in no time! But I’m only 25, so I think I’m doing alright with it for now!
No need to speed in a Cadillac! You'll always get to where you're going. Just avoid the Highways....
Putting an update in here primarily for me-
I did more road testing (really just joy riding around after work) tonight, and while I do feel like perhaps there is some drive train vibration, I really feel like the vibration is coming from the 4 corners. I have new ball joints coming and new front shocks as well. then a trip to the tire shop so they can install those new parts and get a good road force balance on all 4 tires. After that, we will see where we are. I think an alignment is in order as well.
A few questions I'll pose to the thread-
Should tired be balanced w caps on or off? Ill make sure to have the shop put the weights on the inside as to not interfere with the caps.
Any special needs for doing an alignment? Or fairly straight forward-something that any tire shop should be able to handle?
Thanks!
Logan
I see very few cars from the 60s around here at car shows! Last summer, I was almost always the only Cadillac. If I wasn’t, there was only one other, usually newer.
Love my 64!
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 11 hours ago. 3 Replies 0 Likes
I plan to do a full write up when this project is complete, however, I figured someone may get some benefit of seeing the progressions I make and the steps I took to get there. This also is a good…Continue
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch yesterday. 2 Replies 0 Likes
I have a 1963 Cadillac differential with 80K on it. Found a limited slip a while back, and I do not think I will ever used the original diff. In is in carlsbad California 92009. Let me know if you…Continue
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies 0 Likes
The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion on Monday. 0 Replies 0 Likes
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by