Comment
I often have to type this out online and in email and will create a separate blog, tag it, and put put a link on our Help Topics page.
Jason.
- remove upper and lower phillips finish screw holding the a-pillar finish trim and remove trim.
- remove 3 finish phillips screws at top of chrome instrument cluster bezel that scew up and into clips in the dash.
- remove two 5/16" hex head metal screws inside glove box up top to left and right of latch that screw up and into clips on the dash.
- use a flat pry bar or large flat screwdriver to gently wedge in behind the "dash legs" come down the far left and just right of driver and snap into the metal dash and gently pry out. These legs have a ball stud that presses into a retaining clip in the dash near the bottom of the dash. Use cloth or something soft behind pry bar to protect dash paint.
==> Note: If you have a 64 Cadillac with AC and the in-car sensor and plastic grill in the outer ridge of the dash just left of center be sure to not grab the plastic grill as it is brittle and will break. Also be sure not to bump it into anything when removing. Treat that piece with respect as they are eash to break!
- with dash legs pulled away from the dash raise the front of dash up and pull out toward you a few inches. There are wire clips at back that engage and holds the dash down and in place. You will sort of feel it release.
- Once raised up a bit, disconnect the wire connectors for courtesy lights (far left and right on 64, center on 63), and optional items if equipped including cruise control control wheel and switch assembly(top left of dash), twilight sentinel photocell dash sensor (64 option on top left front corner of dash), and guidematic phototube (in center top on 63's with guidematic auto-dimming).
- From there lift up, and pull back and out. Depending on condition the vinyl can be very brittle and all it may take is a heavy hand to crack the vinyl... especially across the top where it has baked in the Sun for 48/49 years.
Started by Jason Edge in General Discussion 22 hours ago. 0 Replies 0 Likes
I have been quiet lately, and just wanted to jump in an chat a minute. I have back to back visits to potential CLC Winter Board and Grand National Sites, not to mention I have been pushing to get…Continue
Started by Jason Edge in General Discussion 23 hours ago. 0 Replies 0 Likes
Very busy day working the parts cars yesterday, pulling engine and transmission out parts car #59, getting parts car #60 off the car hauler, then parts car back up on car hauler for final…Continue
Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth on Tuesday. 1 Reply 0 Likes
My 61 year old radiator sprung a leak (actually a few leaks). What are you guys using as replacements? Are you replacing with copper or aluminum? How many rows are you running in the radiator? How's…Continue
Started by Jeff Donaldson in Wanted to Buy on Monday. 0 Replies 0 Likes
Hi,I need one T-3 low beam headlight if anyone has a spare they would like to sell.CheersJeffContinue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website