"The seat you see in the picture was redone with the original material Russ, this swatch of material does not match. I think the 64’s had a light blue which I have, and a teal blue which this material is. I purchased this material thinking it…"
-
Ray Schick
- Male
- Chicago, IL
- United States
- Blog Posts (4)
- Discussions (63)
- Events
- Photos (4)
- Photo Albums
- Videos
Ray Schick's Discussions
Bumper Bucket
Started this discussion. Last reply by 3gk350qap28u3 Nov 4, 2022. 1 Reply 0 Likes
Somebody better scoop this up it was just posted on eBay & free shipping !…Continue
Oil pump priming ,
Started this discussion. Last reply by Ray Schick Nov 3, 2022. 7 Replies 0 Likes
Pulled the distributor and used a drill to prime the engine , Question, is oil suppose to shoot out of the gear shaft ? Been turning the gear clockwise pContinue
Front cover
Started this discussion. Last reply by Ray Schick Dec 30, 2021. 1 Reply 0 Likes
Horn
Started this discussion. Last reply by Jason Edge Feb 23, 2020. 9 Replies 0 Likes
Ray Schick's Page
Latest Activity
"Take the bottom seat cushion out and you will see the original color on the bottom of the seat. "
"Question: what are those specs. on the oil pump gear wells on the front cover ?"
Bumper Bucket
Somebody better scoop this up it was just posted on eBay & free shipping !See More
"Thanks for everyone’s response, it seems like it’s solved ,took off the valve covers, and even pulled the oil pressure switch ran the drill for a good 10 minutes finally oil shot out of the switch port and oil is bleeding out of…"
"Probably just need to perform the step below. After that, try priming with the drill again. If you feel resistance on the drill, you are good to go."
"If I remember correctly when I primed mine, I didn't see oil shooting out of the shaft gear but definitely felt resistance on the drill when the pump was primed and pumping oil. At 1st the drill will spin freely and when oil is pulled in you…"
"Put the distributor back in ,set timing. Still seems to be a valve train noise ,shut it down .oil is up to level.filter is full of oil . Should I pack the gears with petroleum jelly ?and fill the oil filter neck with oil . Prior to this I had the…"
Oil pump priming ,
Pulled the distributor and used a drill to prime the engine , Question, is oil suppose to shoot out of the gear shaft ? Been turning the gear clockwise pSee More
"Sammy, check out the help section,look up alignment. You’ll see that there where other members who had alignments done with those adjusted numbers that have been successful for these cars with radial tires. It worked for me "
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Coupe Deville
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 27725
- 1963/64 Cadillac Chapter Member?
- yes
Ray Schick's Photos
Comment Wall (2 comments)
- At 9:53pm on November 7, 2012,
Raymond Peter Bombeck Sr. said…
Boy didn't mean to copy what you said about mine but
Sweeeeeeeeet says it all
- At 7:36pm on November 5, 2012,
Jason Edge said…
Hi Ray,
Welcome to the 63/64 Cadillac Website. Be sure and check out all the links and pages and make yourself at home.
Jason.
Ray Schick's Blog
New old stock seat material
Posted on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Photos
Members
Forum
Anyone Ever Hear of or Use Gary's Steering Wheels
Started by Jason Edge in Restoration Discussion 14 hours ago. 0 Replies 0 Likes
Scanning thru the Feb issues of Hemmings I found a listing for Gary's Steering Wheels. I didn't think I had heard of them but looked on our …Continue
Dino Diaries - Turbo HydraMatic Starter Bolts Replaced
Started by Jason Edge in 1963/64 Cadillac Specific Discussion 14 hours ago. 0 Replies 0 Likes
While I have most of the fasteners mapped out and selling with new cadmium plating, for the top side stuff, there are nuts, bolts and washers, etc. on the underside I have not completely mapped out.…Continue
Dino Diaries - All Jacked Up For Christmas!
Started by Jason Edge in General Discussion. Last reply by Jason Edge 14 hours ago. 3 Replies 0 Likes
I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue
Dino Diaries - 165,567 Miles & Counting
Started by Jason Edge in General Discussion. Last reply by Jason Edge 14 hours ago. 2 Replies 0 Likes
I always get a kick out of the expression when someone asks how many…Continue
Blog Posts
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Vintage Air AC
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Events
Videos
© 2025 Created by Jason Edge.
Powered by
