Started this discussion. Last reply by 39991p10fah2l Jul 22, 2014. 4 Replies 0 Likes
If anyone has a "ready to bolt in" antenna assembly available, I would be interested in talking. Drop me a line. Thanks, TedContinue
Tags: antenna
Posted on February 26, 2013 at 11:45pm 1 Comment 0 Likes
Trying to work on the clock out of my 64. When I put a charge to it, the contact points chatter back and forth, sounding like a doorbell buzzer. I don't see the gears moving and the points never snap back. Has anyone experienced this? Ted
Posted on February 26, 2013 at 11:45pm 0 Comments 0 Likes
Trying to work on the clock out of my 64. When I put a charge to it, the contact points chatter back and forth, sounding like a doorbell buzzer. I don't see the gears moving and the points never snap back. Has anyone experienced this? Ted
Posted on January 3, 2013 at 12:59am 0 Comments 0 Likes
I found an old article I had printed years back on servicing our dash clocks. The article states to remove the three screws around the perimeter of the bezel and then the nut in the back. The back of my clock has a reddish washer (right in photo) that is pressed into the hole where the power cord prong extends. How do I get this out to clean the inside of the clock? Am I missing something? …
ContinuePosted on November 22, 2012 at 1:22pm 1 Comment 0 Likes
Happy Thanksgiving to all! I'm looking for the listing of paints for under the hood. Detailing the engine is my next challenge! I know this was on the old site but could not find it on the new site. Thanks.
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies 0 Likes
Hey everyone, I need to replace my transmission input seal before spring starts, I’ve been losing a lot of fluid post Sunday drive. I figured I’d do the rear main seal service bulletin at the same…Continue
Started by Michael Monson in Wanted to Buy. Last reply by Michael Monson yesterday. 2 Replies 0 Likes
Looking for a heater control valve 9.795 for my 1964 Deville. ThanksContinue
Started by Jeff Donaldson in General Discussion. Last reply by Logan Robb on Tuesday. 4 Replies 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt on Sunday. 7 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2026 Created by Jason Edge.
Powered by
Comment Wall (1 comment)
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website
Hi Ted.Welcome to our new site!
Jason.