Per Tony,  i am starting a new thread on my adventures with this rear main leak,

i posted a video on a 390 engine of a rear main seal replacement but the engine was out of the car,, gave some insight as to sealing and materials etc.

One of my neighbors has a hoist,(yeah!) and has allowed me to use it,, makes it a lot easier than rolling around on the asphalt in the street and is enough higher that its not too confining under there.  I did have to pay attention to the lift points though as it seems you cant just put those lift arms wherever you want..

As of this evening, I have taken the exhaust loose, the steering loose, and the starter is out,, took about 4 hours to do that.  I guess there is nothing earthshaking to report on any of this.  Tomorrow, I will take the pan off and proceed from there.

To be clear before proceeding.

the 63 manual says to insert the bearings in there slots, do not pull off wax coating as that will aid in insertion.  I do not see any wax on my gasket, so my guess they had it on the old ones.,, 

Now, the question here is,, do i add a touch of oil or something to aid in that insertion process,, the manual does not suggest it, as i describe above, or, just insert dry, as is..

it does say apply rubber cement to cap and block mating surfaces, and gasket ends, but that is the only reference in the 63 manual regarding lubricaitng the seal for installation,,  so is that correct?? insert dry??

the you tube video says to use lubridation after insertion so it wont be dry on start up, so i plan to do that as well.

i will try to take a few photographs of things once i get the pan off,  i m sure most have seen the underside, but its my first venture in there and post them for reference.

Views: 1297

Reply to This

Replies to This Discussion

Whew!  Was worried about that.  Thanks

I can't say, I even remember what the mod looked like when Shane did it. I just remembered he did make a mod to it. I wonder if I have a pic someplace that shows it?

KIm, the engine is not damaged, so no harm done. What counts is that you are doing the work and learning. 

Which way does exhaust gasket face .? Metal side up or down.  Minewas so degraded, i couldnt tell

Never mind,  i got it figured

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith on Tuesday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service