I believe the shop manual refers to the vacuum dash pot on the throttle relay lever as a check valve. I have finally corrected the other vacuum leaks in the A/C heater system only to find the vacuum unit on the throttle linkage will not hold a vacuum. My question is,  does this diaphragm have a calculated bleed or is it supposed to be vacuum tight? Mine is working with engine vacuum but I can't draw a holding vacuum with my mighty vac hand pump. Thanks.

Views: 345

Reply to This

Replies to This Discussion

It should hold vacuum, and when the engine rpm's drop, the vacuum drops, allowing the plunger to come back out.

I have a good part, just send me an email;  russ85747@hotmail.com

Just to add to the discussion, Cadillac replaced the vacuum fed check valve early during the 1964 model production run, with a spring and orifice type dash pot.  According to the serviceman bulletin they went to the dash pot "to prevent stalling after sudden release of the accelerator pedal." according to the Serviceman Bulletin.  I've got both the vacuum check valve and spring and orifice dash pots.  If you wanted to switch over to the spring and orifice dash pot you would also need the throttle relay bracket it attaches to.  

Thanks guys!

Jason, is upgrading to the 64 design a remove and replace bolt it in, connect the linkage and go task? I like the prospect of eliminating a future vacuum leak if it is R&R then go. Thanks.

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion on Tuesday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith on Tuesday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service