Hoisting engine
Im about to pull engine from car. I have removed valley pan, IM, undone exhaust from EM. Heads still on. Will b using a standard type lift. Hood off. Where is best place to hook up. Do i need one of those brackets. Looking for safest, easiest to manage method
Thanks
Replies to This Discussion
-
Permalink Reply by William R Conte on
-
Are you pulling the transmission with it? If so, I recommend one of these --> https://www.summitracing.com/parts/sum-g1021
It will help balance the load. I will be reinstalling the engine and trans back in my 64 as a unit, and this is the item I got.
When I pulled the engine out by itself, had the intake off of it, and I bolted my chain to two opposing ends at the manifold mounting location. It worked out fine.
-
Permalink Reply by Kim K Kaiser on
-
Thanks, no. Jiat engine. ..so just pust two bolts in were intake attaches on each side and run chain across and up to lift mechanism?
-
-
I used a single chain, and attached it at pass side rear most intake man bolt hole, and driver side front most bolt hole. Hook the hoist at about center of chain and away you go!
-
-
10 4
Members
Forum
Comfort Control working as it should
Started by Christian Doerk in General Discussion. Last reply by Chris McBride 2 hours ago. 1 Reply 0 Likes
Hi friends,after checking all the functions of my Comfort Control of my 1964 Fleetwood, everything is working as it should. The control of the temperature is working really well, except one…Continue
Rear Main Seal Oil Leak Fix with Bearing Cap Modification
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Christian Doerk yesterday. 18 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Coolant Overflow Bottle / Reservoir for 64 Cadillac Eldorado
Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Thursday. 9 Replies 0 Likes
Greetings Everyone. I read a discussion thread about "radiator and related", covering coolant overflow. Has anyone fitted an overflow reservoir / bottle to their 64 Cadillac? Is there if a…Continue
1963 Eldorado Trim complete set
Started by Robert Dye in For Sale on Thursday. 0 Replies 0 Likes
This is complete set of nice 63 Eldorado trim. Would like to sell as complete set but have duplicates of most of the moldings that can be sold separately. I am attaching a few pictures but you can…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
