Matti Roth's Discussions (129)

Discussions Replied To (112) Replies Latest Activity

"Thanks Jason! Actually this is mentioned in Owner’s Manual page 37 but there is no p…"

Matti Roth replied Nov 24 to DIDGAKNOWTHAT? - Notches for Holding License Plate Door Open when "Filling Up!"

3 Nov 24
Reply by Jason Edge

"Factory Shop Manual is your best friend. You need to remove the upper stoppers of th…"

Matti Roth replied Oct 2 to Window Frame removal

2 Oct 2
Reply by Dominic Salemi

"Hi, you need to put 2 o-rings to waterpump. Some people use gasket sealer there as w…"

Matti Roth replied Sep 26 to Water crossover at water pump, leak at O-Ring

7 Sep 27
Reply by Dennis P. DiBari

"balancer not yet in place so you can see the seal saver there"

Matti Roth replied Aug 27 to Front cover leak

5 Aug 27
Reply by Matti Roth

"No, I have not changed them. HD springs is a good idea."

Matti Roth replied Aug 15 to Hi-jackers in 64?

5 Aug 15
Reply by Jason Edge

"Thanks. I think situations when there are several persons sitting on the rear seat.…"

Matti Roth replied Aug 15 to Hi-jackers in 64?

5 Aug 15
Reply by Jason Edge

"Hi jumping the in-car temp sensor reduces the total resistance of sensor circuit, so…"

Matti Roth replied Jun 30 to AC: Can I jump the dash ac sensor wires without harming anything?

2 Jun 30
Reply by Norman Silverman

"Yes there is a clamp "

Matti Roth replied Jun 10 to Stuck Throttle

8 Jun 10
Reply by Logan Robb

"Between the gearbox and electric motor under the driver`s seat."

Matti Roth replied Jun 7 to Trivia 30 - What Is It?!

4 Jun 21
Reply by Jason Edge

"I got my original 64 radiator re-cored. Works fine and looks great! "

Matti Roth replied Apr 30 to Replacement 63 Radiator Recommendations

1 Apr 30
Reply by Matti Roth

RSS

Photos

  • Add Photos
  • View All

Forum

Clock Removal

Started by Jeff Donaldson in General Discussion. Last reply by Jason Edge 12 hours ago. 2 Replies

Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue

Dino Diaries - All Jacked Up For Christmas!

Started by Jason Edge in General Discussion yesterday. 0 Replies

I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue

Power Brake Booster

Started by Stephen Pechenik in General Discussion. Last reply by Bill Wolf yesterday. 13 Replies

Hello Co-Members,I recently purchased a  low mileage1963 Sedan Deville Park Avenue.  It is extremely solid and runs well.  Neverthelss, it has minor problems that need to be addressed before I can…Continue

Body side molding install help needed

Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Wayne Morris on Saturday. 6 Replies

I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service