Looking forward
Thinking a bit ahead, i thougt about the distributor. As i havnt put on the heads and seeing the pistons approach top, would this be a good time tonput it back in. I marked the cap on disassembly, by my spark wires as the were in the car in the old engine. I hvnt put in the distributor before so ive been reading and you tubing to get a visual reference, but most are w engine in and heads on.
I hv my rockers done, my springs and all done, and am looking to attach to block in nxt day or so. Front cover is obviuosly on given HB discussion. So would it be a good idea to try and put it in before heads or after. I know i need to get the bottom end on so, put oil in and prime engine via drill and a 12mm bit, but after that, would the distrubtor be nxt?
Replies to This Discussion
-
Permalink Reply by 3ft7bqmb7dryo on
-
Doesnt matter one way or the other. with the heads on, you can see the piston through the spark plug hole.
-
-
Just make sure that when you install the distributor, you line up the rotor with the piston at the top of the compression stroke.
Members
Forum
Bleeding brakes
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin yesterday. 3 Replies 0 Likes
I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue
Front grill
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Getting hot when going fast…
Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies 0 Likes
So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue
Rainstorm out of nowhere!
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes
After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
-
July 20, 2024 - 63/64 Cadillac Chapter Zoom Meet-Up
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
Videos
© 2025 Created by Jason Edge.
Powered by
