Last fall I replaced my rear yoke and trailing arm bushings . Now with 410 miles on them the large

  rear trailing arm bushings are done . I contacted Rare Parts the maker and they were defensive and

  wanted me to purchase new ones and if sent the old ones back they,  upon inspection would  reimburse the original seller  (Old Parts) a seller on ebay. Seemed like a lot of hoops to jump through so I inquired at all the

known Cadillac Suppliers and it seems the Rare Parts is the only maker of the RP15606 bushings . Further

 internet searches found this is a common problem. This has led to Dan McNarry and Russ Austin heading up making replacement arms with high tech bushings that do not distort and last. Rare Parts needs to retool and use rubber that will last .  In the mean time DO NOT  purchase trailing arm bushings from them with the

expectation they will last as I assure you they will fail quickly

Views: 1283

Attachments:

Reply to This

Replies to This Discussion

Doug

Real sorry you had the problem and experience you have had but thanks so very much for the heads up on the supplier

Enjoy

I put the new trailing arms in all the cars I work on. Huge difference.

Hi Russ 

Could you please describe what you did?

are you making up emplacement rear arms? 

Thanks

Jeff Kinzler

I do not make the trailing arms, I was the test bed for them. Dan makes then. The arm is constructed out of square tubing. Poly bushings are used that are readily available, but the control arms come with them.

It is a complete assembly ready to bolt up. There are no modifications involved.

You can reach Dan at   dmcnarry@telus.net

Real nice solution to the rear end control arm bushing replacement issue

So how much do these wonderful replacements cost to aquire ?

Enjoy

I can also attest to this, put a new set of the Rare Parts rear control arm bushings in a 64 Sedan Deville 2 months ago and after 600 or so miles, they are distorted and sagging worse then the old ones that I had replaced.

I put a pair the McNarry rear control arms in my 64 Fleetwood last year and am very happy with them........should have just did the same with the Deville, but I was just trying to save a few bucks. Will cost me more in the end now!

Here’s a company in Georgia that manufactures this type of bushing: Their size chart is metric  perhaps they could match what is needed for the rear control arm application  

https://www.avproductsinc.com

AV also says that they will make bushings in unique sizes. 

In the mean time I identified another source for rear bushings: Caddy Daddy. Their site also lists the dimensions of the bushings. 

Regards,

Jeff 

I guess, I am just not getting the point of the new control links and bushings. Why doesn't Dan McNarry just put the new bushing (that don't distort) in good refurbished control links? I have a good stash of both 63 and 64 style control links for someone to push the old bushings out and put new bushings in. So, I guess I'm asking if Dan can put bushings that hold up in this "squarish" fabricated control link that will hold up, can't he do the same in a stock control link? My problem with this is the control links look "Frankenstein-ish" and viewed from the rear of car or underneath looks very made-up and un-original. If originality was not a concern, I would have less problem with these... but still look boxy and contrast with the look of the undercarriage. Sort of like dual chrome tips sticking out the end of the car might be fine for what you are after, but those that want a stock look ... like me on my 64 CDV, would cringe at putting these under my 64 CDV.  I applaud anyone taking the initiative to reproduced parts to keep these cars on the road and provide alternative means to an end, but have to be honest and say these are glaringly butt-ugly from my perspective.  They look like something I might expect to see on a rat-rod or down at the strip on a tubbed roadster.

I've had no issues with the stock control links...and find they are pretty tough. I've seen some where people have tried to jack car up on the outer lip and damage, and one or two that may have been in a wreck that bent them but the stock control links are pretty tough. They way they mount to the rear axles and frame give little room for flexing, ... just don't see the advantage other than this has a bushing that holds up well... then again I ask why not just put them in a stock control link?  Is it a matter that Dan cannot find good donor original control links, or cannot put his type bushings in the control link?  So what am I missing? 

I thought the problem being discussed was poor quality bushings from this seller that calls itself “Rare Parts.”

Jason, I think I found the car that goes with those control links:

LOL!

Jeff... my point... why make up an entire new control link that looks "fabricated" when you can just get good used original control links and install the good bushings.

ps.. that would have been my dream car at age 16 ... although I really dug the Keystone Classic Mags.  Those would have made this car righteous!

I agree with you 100%!

RSS

Photos

  • Add Photos
  • View All

Forum

1964 Cadillac Deville - TH400 kickdown switch

Started by Louis in Wanted to Buy. Last reply by Charles Fares 8 hours ago. 1 Reply

Hello,I am searching for a  TH400 transmission kickdown switch (the one near the carburetor). A new one or in good condition.I already asked Fatsco and US Parts Supply but they don’t have this…Continue

New Gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion 10 hours ago. 0 Replies

I am truly fascinated by the  wonderful  inspiring stories behind owning these 63-64 CLASSIC ANTIQUE CADILLACSThey have set the website ON FIRE !!Jason Mr Webmaster your talents regarding the subject…Continue

64 429 Thermostat Housing

Started by Jason A in General Discussion. Last reply by Russ Austin 13 hours ago. 1 Reply

Does anyone know where to find a thermostat housing for a 64 429?  Are any cars interchangeable?  Chevy 350 looks identical, but a lil bigger.Thanks,JasonContinue

New photo gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 16 hours ago. 8 Replies

Having trouble posting my picture in the new gallery but managed to get the text right The computer WIZ - I am NOT ! Stay safe my friends Continue

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service