Interior wood
Quick question......What is the best wood cleaner/polish for the interior wood trim in my 64 Fleetwood?CheersJeffSee More
Jeff Donaldson's Discussions
Interior wood
Started on Tuesday 0 Replies 0 Likes
Quick question......What is the best wood cleaner/polish for the interior wood trim in my 64 Fleetwood?CheersJeffContinue
Clock Removal
Started this discussion. Last reply by Jason Edge Dec 21, 2024. 5 Replies 0 Likes
Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue
1964 AC Compressor
Started this discussion. Last reply by e275bc758eea45bc89d1c8bf39181585 Aug 15, 2024. 2 Replies 0 Likes
Hi,I just had my Automatic Climate Control changed over to R134 and everything worked well but the refrigerant leaked out over night. It turns out my compressor leaks. I'm wondering what the best…Continue
T3 Headlights
Started this discussion. Last reply by Jeff Donaldson May 11, 2024. 3 Replies 0 Likes
Has anyone bought new oem headlights from Lectric Limited? They want $150 for a set of new remanufactured ones. Any advice would be appreciated.JeffContinue
Jeff Donaldson's Page
Latest Activity
"Perhaps; I did have a left and a right....Lol. I installed the one that looked like the one I took out. I'm not going to pull my car out until the end of March so I will report in when I get it figured out. Thanks for your help Jason!
Jeff"
"I installed the same gear as H E sells. It seemed to only go in one way with no room for adjustment but it's possible I got it wrong. No idea.....! I'll have to take it out again and take a look. Thanks for the feedback. "
"Sorry. It opens to 90* not 45. My original passenger vent opens to about 105* as yours do Kurt. I'm pretty sure that I installed the aftermarket gear correctly but maybe not. Has anyone else had the same 90* result after installing the…"
"I installed the aftermarket gear on my left front vent. It opens and closes as it should but only opens to 45*."
"Spray some WD40 around the insulator and it should gently pry out. At worse if it breaks, you can match it up with one of those rubber insulators you can get in the fastener section of Home Depot or Lowes. You might also have it in a warm room or…"
"Hi Jeff,
When I pulled my clock last year, I removed the clock and disconnected the hot wire off and removed the light by twisting it out. I had the clock repaired by Clock Works and they sent it back fixed. I did not…"
"Hi Dennis,
Thank you for your tip. I bought the jar opener and the clock popped out easily. Now I have another question. Does the spade connector with a pinkish colored insulator on the back of the casing screw out or should it just pull off. After…"
"Dennis is correct on all accounts, especially about disconnecting battery. I will add that with the dash pad off I have never met a clock I couldn't get a grip and turn our by hand. With dash pad on you really don't have much room to get a…"
"Hi Jeff,
I have a 1964 Series 62 and have removed my clock myriad times. I use a rubber type band (the kind you use to open tight jars) and wrap it around the outer part of the clock (the outermost part - about 1/4"…"
Clock Removal
Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately 60*). Maybe I don't have enough strength for that sort of thing anymore. I'm wondering how much torgue it takes to get it to rotate out. I looked at some pictures and have an idea of how the clock is attached to the bezel, I also noticed that the bezel is attached to the cluster frame by only 2…See More
"If it were my car, I would buy a newer version of the originals. Better output and you know it is new or rebuilt. Finding a NOS would be near impossible and it will have 60 year old seals."
1964 AC Compressor
Hi,I just had my Automatic Climate Control changed over to R134 and everything worked well but the refrigerant leaked out over night. It turns out my compressor leaks. I'm wondering what the best solution would be. Get my unit rebuilt, buy a rebuilt unit off the shelf or try to find a NOS unit? Does anybody want to weigh in? I also need to know the best places for the service needed or part. ThanksJeffSee More
"Thank you both for your help. I'll go ahead and order a set."
" I have a set in my 60 coupe , I had a set in the 64 Eldo I sold I had them in when judged, I also have them in my 63 fleetwood. https://www.lectriclimited.com/product/sealed-beam-bulb-set-5/"
"I have never bought reproduction T-3's. I didn't know (or perhaps have forgotten) that anyone was reproducing them. Can you provide a link?Just fyi. I now have a large stash of the inner T-3's (the hi beams), but stay out of the more…"
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Fleetwood
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- No
- 1963/64 Cadillac Chapter Member?
- No
Comment Wall (1 comment)
- At 8:07pm on July 10, 2023,
Jason Edge said…
Welcome to the 63/64 Cadillac Website.
This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the Chapter.
- Click on www.join.6364cadillac.com for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club.Be sure and check out all the links and pages and make yourself at home. The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.
Photos
Members
Forum
Interior wood
Started by Jeff Donaldson in Restoration Discussion on Tuesday. 0 Replies 0 Likes
Quick question......What is the best wood cleaner/polish for the interior wood trim in my 64 Fleetwood?CheersJeffContinue
WTB: passenger side C-pillar trim piece 63 SdV
Started by Mark Geertsma in Wanted to Buy. Last reply by Jason Edge on Monday. 1 Reply 0 Likes
I’m looking for the small passenger side C-pillar trim piece (roughly the division between roof and body) for my 63 Sedan de Ville. This is not the wide molding that extends sideways from the rear…Continue
Rescan of November 1962 Serviceman Bulletin Uploaded
Started by Jason Edge in General Discussion Jan 26. 0 Replies 0 Likes
Back in November I started rescanning the Serviceman Bulletins as a…Continue
Dino Undercarriage Restoration Continues Rearward at the Frame to Body Support Flat Braces
Started by Jason Edge in Restoration Discussion Jan 24. 0 Replies 1 Like
After making a decent start on cleaning up a section below right rear area of my my 64 Coupe de Ville - Dino's undercarriage, I have been slow to make more progress but in the last couple of days…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
-
February 15, 2026 - 63/64 Cadillac Chapter Zoom Meet-Up
February 15, 2026 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
Switch to the Mobile Optimized View
© 2026 Created by Jason Edge.
Powered by
