"Hi Chris,
This is really some fine work you did with the timing cover. As always, I'm very impressed with the work you do and what you discovered with the pinhole. Kudos to you and Russ!
Dennis DiBari"
-
CHRIS CARLSON
- Male
- Parkers Prairie, MN
- United States
- Blog Posts (2)
- Discussions (30)
- Events
- Photos
- Photo Albums
- Videos (1)
CHRIS CARLSON's Discussions
Timing cover corrosion
Started this discussion. Last reply by Dennis P. DiBari Jul 15. 1 Reply 0 Likes
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue
They do exist!
Started this discussion. Last reply by Chris Codd Feb 3. 2 Replies 0 Likes
An individual on Facebook was parting out a 1964 429 and transmission from a 70,000 MI sedan DeVille for an LS swap got lucky and scored this dent free oil cap before it hit the scrap iron pile with…Continue
Cruise control
Started this discussion. Last reply by Patrick Westphal Mar 31, 2024. 5 Replies 0 Likes
Is anyone using an aftermarket cruise control on there 64 Cadillac? what brand & model did you purchase?Continue
Cadillac horns
Started this discussion. Last reply by Jason Edge Jan 15, 2024. 3 Replies 0 Likes
I was going through one of my Sun test equipment cabinets & found this Delco Remy original electrical equipment booklet for GM passenger cars from 1965. It was interesting to see the trumpet…Continue
CHRIS CARLSON's Page
Latest Activity
Timing cover corrosion
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a little more oil pressure he likes to see about 40 lb not 30. had a little too much oil pressure 100 lb remove the oil pump cover to remove the shim engine oil was all milky it had only run about 5 seconds before we shut it down removed the drain plug and ran the oil out it was all milky a little stream…See More
"Did you have this problem prior to installing your Pertronics ? I work on distributors and have seen some of these point conversions cause problems. Reduce timing to 5 degs, check that your vacuum advance is working properly. is your…"
"Did they come with one or two wedge blocks ?"
"I'm going on friday but just to spectate"
"Michael, You would remove the intake manifold and replace the gaskets with the block off style gasket, or you could use regular gaskets and just cut a piece of tin and place over the exhaust crossover port on each side. I also removed the heat riser…"
"I have installed an electric chock on my 4GC Rochester carb. I also installed Olson intake gaskets with the exhaust cross over blocked. I have electric chock stats on hand for the Rochester , you can also purchase them from Mikes Carburetor . If…"
" Dave , Can you use an oxy acetylene torch to heat the flange that the joint goes into in the diff housing red hot then quench it with cold water that should get it loose. "
"Logan, I purchased all my brake parts from Kanter auto. wheel cylinders, hardware kits, brake hoses, and brake shoes. for my Fleetwood sixty Don't throw away your old brake return springs, & hardware because you will want to retain…"
"Logan , I purchased my front end parts from Kanter auto . But have not installed them yet. "
"Hey Jason , Glad to here the surgery went well ! The Neurologist at the Mayo clinic told me to take vitamin B-12 to help my damaged nerves recover, nerves like B-12 nerves take the longest to recover after surgery or being damaged…"
"Great video Chris on the engine honing.
Dennis DiBari"
May 16, 2024
The correct way to hone a 429 Cadillac block using a torque plate.
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Fleetwood series 60
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 34518
- 1963/64 Cadillac Chapter Member?
- yes
CHRIS CARLSON's Videos
CHRIS CARLSON's Blog
accumulator dryer
Posted on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
1964 power steering sector rebuild
Posted on March 20, 2023 at 11:32pm 1 Comment 0 Likes
I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response, has anyone done this? and how do you like it? thank you
Comment Wall (2 comments)
- At 10:36am on February 3, 2025,
Dennis P. DiBari said…
Great video Chris on the engine honing.
Dennis DiBari
- At 4:07pm on March 20, 2023,
Jason Edge said…
Chris,
Welcome to the 63/64 Cadillac Website and 63/64 Cadillac Chapter.
This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. As a CLC member you are eligible to join our free 1963/64 Cadillac Chapter and will get you signed up in a bit.
Be sure and check out all the links and pages and make yourself at home. The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.
Photos
Members
Forum
Trivia #34 - What % of 1963 & 1964 Cadillacs Came with Tinted Glass
Started by Jason Edge in Trivia 2 hours ago. 0 Replies 0 Likes
What % of 1963 and 1964 Cadillacs came with the optional "soft ray" tented glass? 1963 & 1964 were very close, so if you get one you will get the other. Need to get it within 3%. So, who will…Continue
Trivia #33 - What % of 1963 Cadillacs Came with Limited Slip (Posi) Differential Rear End
Started by Jason Edge in Trivia. Last reply by Jason Edge 2 hours ago. 3 Replies 0 Likes
It has been way too long since we posted any trivia (and gave out a cigar), so here is one I thought I might have posted but do not see it: What % of 1963 Cadillacs came with the optional "Controlled…Continue
1963 Coupe de Ville Located in NC For Sale
Started by Jason Edge in For Sale. Last reply by Jason Edge on Friday. 2 Replies 0 Likes
I had an older couple contact me indicating they are selling their 1963 Coupe de Ville they have had for 40 years and they are located Moyock, NC, which is in the very north east part of North…Continue
Front grill
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Thursday. 15 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
-
December 14, 2025 - 63/64 Cadillac Chapter Zoom Meet-Up
December 14, 2025 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by
