"Thanks Jason, I'll give it another try with some help."
-
James Barnes
- Male
- Rancho Mirage, CA
- United States
- Blog Posts
- Discussions (4)
- Events
- Photos (8)
- Photo Albums (1)
- Videos
James Barnes's Discussions
Wanted! 64 Passenger side exhaust manifold
Started this discussion. Last reply by Dennis P. DiBari Feb 12, 2025. 1 Reply 0 Likes
Looking for a passenger side exhaust manifold for my 64 Cadillac. Good condition, free of cracks etc. I found one in FL that had been restored but the guy wants $1595 for it, sounds pretty high to me.Continue
Gear for power vent window
Started this discussion. Last reply by SK Feb 9, 2025. 13 Replies 0 Likes
Im having a hard time locating the gear for the power vent window in my 64 Eldo. The existing one has 14 teeth and all I seem to be finding are ones with 17 teeth. Any suggestions?ThanksContinue
James Barnes's Page
Latest Activity
"Jason, The problem is that they don't move easily. I have tried using a long pipe for leverage to no avail."
"Hi James,
That seems exorbitant. I am sure Jason Edge can suggest something.
Dennis DiBari"
Wanted! 64 Passenger side exhaust manifold
Looking for a passenger side exhaust manifold for my 64 Cadillac. Good condition, free of cracks etc. I found one in FL that had been restored but the guy wants $1595 for it, sounds pretty high to me.See More
"Does anyone know how to adjust the torque rods? The shop manual only says that if they are in the top position, the trunk is easiest to open and most pressure needed to close. Both of the rods on my car are in the middle position but when the trunk…"
"The original gears seem to indeed have - or in my case had - only 14 teeth, while the reproduction has 17. I bought mine either from Hydro Electric or from TA Motor in Sweden. I believe it only opens 90 degrees.
Additionally, the other end of the…"
"Perhaps; I did have a left and a right....Lol. I installed the one that looked like the one I took out. I'm not going to pull my car out until the end of March so I will report in when I get it figured out. Thanks for your help Jason!
Jeff"
"Perhaps you put the RH side on LH side and vice versa? You can look at the stock pictures for comparison when you pull them if not stamped L & R."
"I installed the same gear as H E sells. It seemed to only go in one way with no room for adjustment but it's possible I got it wrong. No idea.....! I'll have to take it out again and take a look. Thanks for the feedback. "
"The 17 tooth gears sold by HydroElectric that I installed and I believe Kurt open the window well past the 95 degree angle. I can opening it until it is pushing air back and at me like seen in Kurt's pictures.You can find them on eBay as seen…"
"Sorry. It opens to 90* not 45. My original passenger vent opens to about 105* as yours do Kurt. I'm pretty sure that I installed the aftermarket gear correctly but maybe not. Has anyone else had the same 90* result after installing the…"
"I actually upgraded my car to power vents and noticed that the manual crank vents did open wider. I just assumed it was normal for the power vents to open less wide but don't know if the replacement gears are a factor there. The original gears…"
"I installed the aftermarket gear on my left front vent. It opens and closes as it should but only opens to 45*."
"I went back & checked the gears I replaced a while back & yes, the originals have 14 teeth. I don't have any pictures of the steel replacement gears I installed so I can't say for sure how many teeth they have. The picture of the…"
"The ones from Caddy Daddy and ebay have 17 teeth, mine have 14 teeth but I eventually found them elsewhere.
thanks"
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Cadillac Eldorado
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 35409
- 1963/64 Cadillac Chapter Member?
- I hope to be
James Barnes's Photos
Comment Wall (3 comments)
- At 5:07pm on September 24, 2024,
Dennis P. DiBari said…
You picked a great one. See you at the Zoom meeting in October. Jason does a great job with this chapter!
Dennis DiBari
- At 4:26pm on September 24, 2024,
Hi James,
I love your 64 Eldorado. It's a great color and clean as a whistle.
Dennis DiBari
Cottekill, NY
- At 2:21pm on June 24, 2024,
Jason Edge said…
Hi James, Welcome to the 63/64 Cadillac Chapter & Website. Be sure to tell us about your 64 Eldorado when you get a chance. Jason.
Photos
Members
Forum
Rear Main Seal & Transmission Pump Seal
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion 17 hours ago. 0 Replies 0 Likes
Hey everyone, I need to replace my transmission input seal before spring starts, I’ve been losing a lot of fluid post Sunday drive. I figured I’d do the rear main seal service bulletin at the same…Continue
Heater Control Valve
Started by Michael Monson in Wanted to Buy. Last reply by Michael Monson yesterday. 2 Replies 0 Likes
Looking for a heater control valve 9.795 for my 1964 Deville. ThanksContinue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Logan Robb on Tuesday. 4 Replies 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Burning Rubber
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt on Sunday. 7 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
