"The seat you see in the picture was redone with the original material Russ, this swatch of material does not match. I think the 64’s had a light blue which I have, and a teal blue which this material is. I purchased this material thinking it…"
-
Ray Schick
- Male
- Chicago, IL
- United States
- Blog Posts (4)
- Discussions (63)
- Events
- Photos (4)
- Photo Albums
- Videos
Ray Schick's Discussions
Bumper Bucket
Started this discussion. Last reply by 3gk350qap28u3 Nov 4, 2022. 1 Reply 0 Likes
Somebody better scoop this up it was just posted on eBay & free shipping !…Continue
Oil pump priming ,
Started this discussion. Last reply by Ray Schick Nov 3, 2022. 7 Replies 0 Likes
Pulled the distributor and used a drill to prime the engine , Question, is oil suppose to shoot out of the gear shaft ? Been turning the gear clockwise pContinue
Front cover
Started this discussion. Last reply by Ray Schick Dec 30, 2021. 1 Reply 0 Likes
Horn
Started this discussion. Last reply by Jason Edge Feb 23, 2020. 9 Replies 0 Likes
Ray Schick's Page
Latest Activity
"Take the bottom seat cushion out and you will see the original color on the bottom of the seat. "
"Question: what are those specs. on the oil pump gear wells on the front cover ?"
Bumper Bucket
Somebody better scoop this up it was just posted on eBay & free shipping !See More
"Thanks for everyone’s response, it seems like it’s solved ,took off the valve covers, and even pulled the oil pressure switch ran the drill for a good 10 minutes finally oil shot out of the switch port and oil is bleeding out of…"
"Probably just need to perform the step below. After that, try priming with the drill again. If you feel resistance on the drill, you are good to go."
"If I remember correctly when I primed mine, I didn't see oil shooting out of the shaft gear but definitely felt resistance on the drill when the pump was primed and pumping oil. At 1st the drill will spin freely and when oil is pulled in you…"
"Put the distributor back in ,set timing. Still seems to be a valve train noise ,shut it down .oil is up to level.filter is full of oil . Should I pack the gears with petroleum jelly ?and fill the oil filter neck with oil . Prior to this I had the…"
Oil pump priming ,
Pulled the distributor and used a drill to prime the engine , Question, is oil suppose to shoot out of the gear shaft ? Been turning the gear clockwise pSee More
"Sammy, check out the help section,look up alignment. You’ll see that there where other members who had alignments done with those adjusted numbers that have been successful for these cars with radial tires. It worked for me "
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Coupe Deville
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 27725
- 1963/64 Cadillac Chapter Member?
- yes
Ray Schick's Photos
Comment Wall (2 comments)
- At 9:53pm on November 7, 2012,
Raymond Peter Bombeck Sr. said…
Boy didn't mean to copy what you said about mine but
Sweeeeeeeeet says it all
- At 7:36pm on November 5, 2012,
Jason Edge said…
Hi Ray,
Welcome to the 63/64 Cadillac Website. Be sure and check out all the links and pages and make yourself at home.
Jason.
Ray Schick's Blog
New old stock seat material
Posted on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Photos
Members
Forum
Power Booster Install
Started by Rob Spring in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 1 hour ago. 6 Replies 0 Likes
Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue
Complete Front End Rebuild
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata on Thursday. 1 Reply 0 Likes
I meant to make this a priority over the winter and didn't get that far. I've tried to source all the parts individually, but that is a daunting task. Partly because I don't want to miss any…Continue
1964 Cadillac Deville Neutral Safety switch and Oil Filter Housing Assembly
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
A Shout Out to Alan Grist & Some Pictures of His 1964 Series 62 4W Sedan
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari on Wednesday. 2 Replies 0 Likes
As they say, Better Late Than Never!I want to give a shout out to 63/64 Chapter Member Alan Grist, who brought his 64 Series 62 Four Window Sedan, to the 2025 CLC Winter Board Meeting in Chattanooga,…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
