per the shop couple weeks ago and a loose steering and a steering gear replacement, it was suggested the left outer tie rod be replaced,, 

I dug not the manual, and can seem to find the directions on that, but did go to you tube and saw about 4 different iterations, and while it seemed simple,, i noticed the connection point is not the same,  on the videos, they just loosen a nut, you mark the spot and then spin out the tie rod end.. on outs, it has two clamp looking items..

is the process the  same,undo those two clamps, or one of them, make the distance or count the rotations out, then spin back in the new one at the same rotations..?

I'm aware it will have to be re aligned, but want to make sure the process is same,, just a different measuring and connection mechanism.??

sincerely

Facebook Facebook

Views: 142

Reply to This

Replies to This Discussion

Kim, you'll only loosen  the outer clamp next to the outer tie rod joint. Leave the inner clamp tight on the inner tie rod. Remove the outer tie rod pivot from the knuckle. Measure the outer tie rod from the edge of the adjuster sleeve to the center of the pivot stud big end. Remove the old tie rod end from the adjuster sleeve. Install the new tie rod end  to the same measurement as the old one was. Put the pivot stud in the steering knuckle torqued to spec. Then tighten the adjuster sleeve clamp. You'll need to get an alignment after you finish your install.  HTH

I got that thing off,  had to get that tuning fork piece to separaye it.  

Getting back on was no prob.  I deceded to order the other side as well as i am in get stuff done mode and will take in for realignment so both sides will hv new parts.  Made sense to me.

I am really surprised at how just changing the one side improved my steering,   i had about a 3 to 4 inch looseness on each side of the steering wheel.  It was enoigh for me to not like driving at night because the over steer and compensation to get back made me look like inwas drinking.  

Anyway, seems to have worked, otherside replacement may get it completely tuned in with alignment.

Thanks again

Thanks, that gave me the clarificaion i needed on the connections

RSS

Photos

  • Add Photos
  • View All

Forum

1963/64 Cadillac Chapter July 2025 Newsletter Posted

Started by Jason Edge in Newsletters 7 hours ago. 0 Replies

I have just completed and posted the July 2025, 1963/64 Cadillac Chapter Newsletter to our…Continue

Tags: Chapter, Newsletter, Posted, Cadillac, 1964

1963 AC evaporator core leaking?

Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Kenneth Barton 18 hours ago. 4 Replies

Hi all,Again I have issues with my AC system. Had it refilled recently but within a few days the system was empty again. The AC mechanic added tracer fluid to check for leaks, but there are no…Continue

Tags: 1963, core, evaporator, AC

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Tony Prichard yesterday. 4 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Power steering fluid

Started by Bobby Brown in General Discussion. Last reply by Tony Prichard yesterday. 7 Replies

My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service