Dash Pad Removal
I’m have a bit of a hard time removing the interior chrome windshield side moulding trim necessary to remove the dash pad. I’ve removed the screws, but the trim does not seem lose and I don’t want to force it. How do the chrome pieces actually lift out?
Replies to This Discussion
-
Permalink Reply by Jason Edge on
-
With bottom and top screw out, grab near the top and pull down and inward. After being installed 60 years the stick a bit, but with firm prying down and out, the inner A pillar ultimately will pop loose.
-
Permalink Reply by Michael Vogler on
-
Thanks Jason. I'll give that a try.
Also, I want to pull the black and plastic Radio Face Plate (see picture). I've managed to get 5 of the 6 screws out, but one screw is impossible to see and is down near the ignition switch. It appears it can only be reached with a small open end wrench, but I just can see it. (on of the reasons I am pulling the dash cover. Any thoughts about getting that last screw out?
Do you have have a nice chrome instrument bezel available? My is okay, but it has some pitting dots. Not horrible, but not clean either.
Thanks, again.
-
-
On road til Jan 30. I can check for bezel when I get home.
-
-
Got them off! Thanks, again!
Photos
Members
Forum
Burning Rubber
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 21 hours ago. 7 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari Feb 16. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson Feb 15. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
