Kim K Kaiser's Discussions (741)

Discussions Replied To (640) Replies Latest Activity

"When getting the car up,, do i need to allow the wheels to hang or can i use a ramp…"

Kim K Kaiser replied 7 hours ago to STEERING GEAR

12 2 hours ago
Reply by Mark S Anderson

"Ok, Saturday, i put the car back together after the third rear seal replacement,  th…"

Kim K Kaiser replied yesterday to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"HI Tony,  the seal just wont go flush to the bottom, it keep s popping bk up,  but w…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"Ues. I put it on bootom and  on top of this rubbersea . Dnr kno if i put it on outer…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"Ok.  Good, thes are the replaces seals going in today.  Bottom half arrached.  The e…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"Does this look correct?  Fat part to rear , flat lip to front?p"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"Ok. This may seem odd but the rear oil pan seal has a cut out along edg,  see pictur…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"Could be!  It went in much smoother than the first one as i had it covered in oil, b…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"i got back under car to see if i can pinpoint leak, i took off the inspection plate,…"

Kim K Kaiser replied Oct 16 to Rear main Follow up replacement and repair,,

40 yesterday
Reply by Tony and Ginny 429

"ok,  thanks,, i will have to get a good picture with description of those parts so i…"

Kim K Kaiser replied Oct 16 to STEERING GEAR

12 2 hours ago
Reply by Mark S Anderson

RSS

Photos

  • Add Photos
  • View All

Forum

STEERING GEAR

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Mark S Anderson 2 hours ago. 12 Replies

IN addition to the main seal leak,,which i am going to tackle again tomorrow,i also have a leak in what seems to be the steering gear.  I have checked to connections from the pump, and its dry on…Continue

What front springs to use to level car back out after an LS swap?

Started by Richard Biele in 1963/64 Cadillac Specific Discussion 9 hours ago. 0 Replies

I see other members have put LS engines into their cars. I am wondering what springs you put in afterwards. I cannot determine the height due to the car having a front end fire (how I ended up with…Continue

2020 Cadillac calendars.

Started by Russ Austin in General Discussion 12 hours ago. 0 Replies

I just got in the 2020 Classic Cadillac calendars.  12 months of 63-64…Continue

Henry Leland- founder of Cadillac and Lincoln

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 2 Replies

Here's a good article about Henry Leland. I had heard bits & pieces of his story over the years but didn't know all these details.…Continue

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service