David Thomas's Discussions (38)

View

Discussions Replied To (32)	Replies	Latest Activity
" I was able to get the A/C control panel out this morning. As Jason suggest from the…" David Thomas replied Oct 10, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"Thanks Russ. I suspected that you or Jason had been there before. I'll try that when…" David Thomas replied Oct 9, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"Thanks Jason. The path looked better going out the top but I couldn't get it past t…" David Thomas replied Oct 8, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"I'm still chasing vacuum leaks on the 63 A/C system. Trying to remove the A/C contr…" David Thomas replied Oct 8, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"On the 63, I think the blower housing could be removed after removing the heater box…" David Thomas replied Sep 30, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"Hi Tony, thanks for the kind words. As Russ and I stated, no need to remove the hood…" David Thomas replied Sep 29, 2019 to Had to replace A/C Mode Damper Actuator	16	Oct 12, 2019 Reply by David Thomas
"The pan and gasket are supposed to be assembled dry without any sealer etc. If seale…" David Thomas replied Sep 11, 2019 to Transmission gasket replacement	34	Sep 11, 2019 Reply by Kim K Kaiser
"Kim, you probably have the pan well sealed. Look a little higher and you will probab…" David Thomas replied Sep 11, 2019 to Transmission gasket replacement	34	Sep 11, 2019 Reply by Kim K Kaiser
"If these are ABS, I would use ABS glue and a thin piece of ABS to fish plate the bac…" David Thomas replied Sep 8, 2019 to Any Hope for this armrest?	17	Sep 10, 2019
"I put a new Airtex pump on my 63, it worked well for 15k miles until the inlet valve…" David Thomas replied Aug 24, 2019 to fuel pump	4	Aug 24, 2019

RSS

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Forum

Rear Main Seal Oil Leak Fix with Bearing Cap Modification

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 14 hours ago. 14 Replies 4 Likes

Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue

Future of CLC Judging

Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge yesterday. 6 Replies 0 Likes

First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue

front seat crest

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Tuesday. 3 Replies 0 Likes

Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue

Coolant Overflow Bottle / Reservoir for 64 Cadillac Eldorado

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Tuesday. 7 Replies 0 Likes

Greetings Everyone. I read a discussion thread about "radiator and related", covering coolant overflow. Has anyone fitted an overflow reservoir / bottle to their 64 Cadillac? Is there if a…Continue

Tags: Radiator, Bottle, Reservoir, Overflow, Coolant

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments 0 Likes

Continue

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes

I bought this seat material thinking that it’s…

Continue

Events

Add an Event

Videos

Guitars & Cadillacs

Added by Kurt 0 Comments 0 Likes
UFCU commercial

Added by Kurt 1 Comment 0 Likes

May 16, 2024 Finish honing with a Torque plate

Added by CHRIS CARLSON 0 Comments 0 Likes

David Thomas's Discussions (38)

" I was able to get the A/C control panel out this morning. As Jason suggest from the…"

"Thanks Russ. I suspected that you or Jason had been there before. I'll try that when…"

"Thanks Jason. The path looked better going out the top but I couldn't get it past t…"

"I'm still chasing vacuum leaks on the 63 A/C system. Trying to remove the A/C contr…"

"On the 63, I think the blower housing could be removed after removing the heater box…"

"Hi Tony, thanks for the kind words. As Russ and I stated, no need to remove the hood…"

"The pan and gasket are supposed to be assembled dry without any sealer etc. If seale…"

"Kim, you probably have the pan well sealed. Look a little higher and you will probab…"

"If these are ABS, I would use ABS glue and a thin piece of ABS to fish plate the bac…"

"I put a new Airtex pump on my 63, it worked well for 15k miles until the inlet valve…"

Photos

Members

Forum

Blog Posts

Events

Videos