David Thomas's Discussions (137)

Discussions Replied To (134) Replies Latest Activity

"Thanks Russ. I suspected that you or Jason had been there before. I'll try that when…"

David Thomas replied Oct 9, 2019 to Had to replace A/C Mode Damper Actuator

16 Oct 12, 2019
Reply by David Thomas

"Thanks Jason.  The path looked better going out the top but I couldn't get it past t…"

David Thomas replied Oct 8, 2019 to Had to replace A/C Mode Damper Actuator

16 Oct 12, 2019
Reply by David Thomas

"I'm still chasing vacuum leaks on the 63 A/C system.  Trying to remove the A/C contr…"

David Thomas replied Oct 8, 2019 to Had to replace A/C Mode Damper Actuator

16 Oct 12, 2019
Reply by David Thomas

"On the 63, I think the blower housing could be removed after removing the heater box…"

David Thomas replied Sep 30, 2019 to Had to replace A/C Mode Damper Actuator

16 Oct 12, 2019
Reply by David Thomas

"Hi Tony, thanks for the kind words. As Russ and I stated, no need to remove the hood…"

David Thomas replied Sep 29, 2019 to Had to replace A/C Mode Damper Actuator

16 Oct 12, 2019
Reply by David Thomas

"The pan and gasket are supposed to be assembled dry without any sealer etc. If seale…"

David Thomas replied Sep 11, 2019 to Transmission gasket replacement

34 Sep 11, 2019
Reply by Kim K Kaiser

"Kim, you probably have the pan well sealed. Look a little higher and you will probab…"

David Thomas replied Sep 11, 2019 to Transmission gasket replacement

34 Sep 11, 2019
Reply by Kim K Kaiser

"If these are ABS, I would use ABS glue and a thin piece of ABS to fish plate the bac…"

David Thomas replied Sep 8, 2019 to Any Hope for this armrest?

17 Sep 10, 2019
Reply by Tony and Ginny 429

"The upper ball joints are side specific. They press into the control arm from the to…"

David Thomas replied Sep 8, 2019 to Replacing upper ball joint question 64 Deville

4 Sep 8, 2019
Reply by Tosh Dickenson

"I put a new Airtex pump on my 63, it worked well for 15k miles until the inlet valve…"

David Thomas replied Aug 24, 2019 to fuel pump

4 Aug 24, 2019
Reply by Anders

RSS

Photos

  • Add Photos
  • View All

Forum

Rear Wheel Bearings Replacement

Started by Dominic Salemi in 1963/64 Cadillac Specific Discussion 29 minutes ago. 0 Replies

HiNeed to replace my rear wheel bearing and seal on my 1964 Conv., does anyone know if its a big project and what I will need before I pull the shaft out? I also need to know the parts number and…Continue

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 34 minutes ago. 4 Replies

The weather here in winter is great for a Cadillac cruise.Continue

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy. Last reply by Kurt 1 hour ago. 1 Reply

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Events

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service