Jason Edge's Discussions (4,210)

Discussions Replied To (3840) Replies Latest Activity

"A description of the cranking system, including the wires and connections, is locate…"

Jason Edge replied May 23 to What does this wire go to

4 May 24
Reply by Kim K Kaiser

"I have plenty of either type. The short tab one on left in your picture for tilt col…"

Jason Edge replied May 18 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"Glad it worked out and good to know only upper brace/bracket needs to be loosened. Y…"

Jason Edge replied May 18 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"I thought I had posted a link to this in the Help Page when I posted it May 2 but ha…"

Jason Edge replied May 17 to A "Fix-It" for Split Windshield Washer Reservoirs that Seems to Hold!

1 May 17
Reply by Jason Edge

"That nut is tack welded to the bracket. You have to loosen from the bolt side. See p…"

Jason Edge replied May 17 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"I guess I'm confused by the "odd bolt (not the usual hex pattern)" statement.  Once…"

Jason Edge replied May 17 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"Well, the column doesn't have to be removed, just lowered a bit. If you have not alr…"

Jason Edge replied May 17 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"This flat headed bolts has a serrated flange headed nut on the front side that secur…"

Jason Edge replied May 17 to Help! 1963 Shifter Bezel and Lens Removal Problem

24 May 19
Reply by Lee Martin

"I have both the washer jet with tip for $10 ($20 for 2) or just the tip for $5 ($10…"

Jason Edge replied May 17 to Windshield Washer Jets for 64 Deville needed

1 May 17
Reply by Jason Edge

"I probably have enough for 2 maybe 3 more sets of these 1963/64 Cadillac top facing…"

Jason Edge replied May 14 to Classic Cadillac Parts For Sale - Misc Items

245 Jun 1
Reply by Jason Edge

RSS

Photos

  • Add Photos
  • View All

Forum

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 3 hours ago. 7 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 16 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

RPM at 70

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 11 hours ago. 1 Reply

I was questioning if my 63 was shifting into 4th , so I installed a tach and don't notice a 3-4 shift. Cruising at 70 the RPM is at 2600. Sounds high.  Has anyone noted RPM's at highway speeds?. I…Continue

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 1 Comment

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service