Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag heavily  a d would not start.  10 min later, it would start fine.   At the time,  i hv cleaned all grounds, all grounds properly,   i wrapped wires withe the heat tape, moved them back from exh manifold,  things seemed ok.

Last cupla weeks,  same symptom,  short rides around town, no problems, always starts, longer rides,  if i get gas,  car barely starts,  sometimes, it doesnt even click,  i can just hear a humm,  after a time or two. , it will slow turn, then start.  

So i got bk under car, notced the black wire had a crack anf i coukd see copper.  As a temp fix, i put electric tape on it,  applied the heat tape,  took out for long ride tonight, 45 min or so at 70,  [no vibrations from rear, yeah!!]

Anyway, i got out, got in,   no start.  

So what testing should i do now,   should i try to rewire from ignition key to solenpoid/starter,   replace solenoid,  what further test can i run that i didnt try in dec.    my limited knowledge says heat has something to do with this,  sustained heat, not just 2 minutes cross town, but longer rides.other than this recurring headache,  car doing good

Views: 1233

Reply to This

Replies to This Discussion

I'm dying here, please stop it Kevin.  Tony's got a wedgie, he will get over it. Come on Tony time to get back to the party. 

C'mon Tony, it'll only stop when you get back on here. PMSL. :-)

Image result for dummy spit photos

RSS

Photos

  • Add Photos
  • View All

Forum

Pick Up of 11th Batch & Drop Off of 12th Batch For Cadmium Plating

Started by Jason Edge in General Discussion yesterday. 0 Replies

As I shared last night in our Chapter Zoom meeting, here is a picture of the 9 totes with fasteners and other parts that will be taken to Winston-Salem NC for cadmium plating. This will be my 12…Continue

Which Shocks for my 64 SDV are MOST like Originals?

Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman yesterday. 4 Replies

I am considering replacing the shocks in my 64 SDV. They're not terrible, but are a little too wishy-washy. I want to replace them with shocks that most closely approximate the original damping rate…Continue

Dino Diaries - A Blast from the Past - 1967 to be Exact!

Started by Jason Edge in General Discussion yesterday. 0 Replies

I love discovering new thing old things about my 64 Coupe de Ville. I bought the car on Nov 13, 1996 from Robert Jessup who lived in Raleigh, NC. The car had some unique early history having first…Continue

Dino Diaries - Feb 22, 2025: Go for the Gold!

Started by Jason Edge in General Discussion on Saturday. 0 Replies

While scooting around under my 64 CDV Dino I am seeing a lot of thinks to address, including swapping in a lot of my gold cadmium plated hardware. Since I am headed to the cad platers in…Continue

Blog Posts

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 5 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

Events

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service