Garage Reorg in Progress - Dino is Happy!
After finishing a new small storage building and shifting some stuff to it from the garage, I have been reorganizing my garage to get to my 64 Caddy "Dino" a lot easier. In years past I flanked 4 long tool boxes down the driver side basically blocking it in. I also had a large work table wedged into the wall and next to my back wall counter meaning I could not really use it much as a work table.
By pulling the work table out in the middle and moving the 4 tool boxes away from “Dino”, with 2 on the back wall and 2 on the end of the big work table, I now have a super sized work area and I can just walk up to Dino and dip under or over and do what I need to do. I have a long way to go in the garage, and another storage building to build but I am getting there!
Here are a few pictures of the reorg with Dino still sitting up on the 12" Race Ramps.
Replies to This Discussion
-
Permalink Reply by Dennis P. DiBari on
-
Jason,
The pictures are fantastic! Dino and the garage are beyond beautiful. I can only pray my garage looks like yours. Your organization is the key!
Dennis DiBari
Photos
Members
Forum
!964 Deville Front Bumper
Started by Patrick Westphal in For Sale. Last reply by Jason Edge 58 minutes ago. 1 Reply 0 Likes
Hey everyone,I have a set of front bumpers, both ends and the center section, that I am looking to sell. If you are looking for these contact me and we will talk about it. …Continue
Which are best Shocks for 64 that are closest to Original in Ride Quality?
Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman 19 hours ago. 5 Replies 0 Likes
Hello AllI am thinking about replacing the shocks on my 64 SDV. I want to do so with units that are closest to what was originally in the car in so far as ride quality. I believe these were gas…Continue
1964 Cadillac Owners - Are You Missing the Inner Fender to Frame Rear Brace Rods?
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 20 hours ago. 1 Reply 0 Likes
Last night I was installing the freshly cad plated inner fender to frame rear support brace rods and remembered how this has been often missing on the many parts cars I have brought in. The thing is…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 22 hours ago. 2 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
© 2025 Created by Jason Edge.
Powered by
