So after some searching, I only found one discussion about replacing the rear main seal. That post was for a 64 DeVille, I have a 63.  The post wasn't clear if the job could be done with the engine still installed in the car.

 Before I go digging into this, can someone confirm if the oil pan and rear main seal can be replaced with the engine still in the car?

Thanks

Views: 76

Reply to This

Replies to This Discussion

Yes it can. The procedure is outlined in the Shop Manual. You should also do the bearing cap modification which has been discussed often here & is in the Help tab above.  

https://6364cadillac.ning.com/forum/topics/rear-main-seal-oil-leak-fix

Thanks, That link gave some great information. Unfortunately, before I joined this group, I went out and purchased an engine  gasket set from Speedway Gaskets. The set I bought was manufactured by Best. I have seen here that the Best brand rear main seal leaks and is not any good. Do you know if the rest of the Best brand of engine gaskets are any good? I have not used anything from the kit I purchased. If they are not any good, since the gasket set is unopened, maybe I can return them.

The other gaskets are good to use. 

That's good to hear, otherwise I might have wasted $200. I bought the gasket set back March. I doubt I would have been able to return them.

DO NOT GET the Best Gasket brand rear main seal. It is a known failing seal. It leaks immediately upon engine start.  I have talked to the company and they don't care. The rubber is too soft and the seal has no pressure on the crank to seal.  

Get with Caddy Daddy and get the rear main seal that they stock. 

How about the other gaskets made by Best Gasket? I purchased a complete engine gasket set before I joined this group. I have not used any of them yet. I was about to replace the front seal. Do you know if those seals are any good?

Yes, the engine stays in the car.  The pan is removed by rotating the crank so the balance weight up front is up top. That gives the oil pan the clearance to be pulled back. 

Loosen the main caps so the crank drops JUST A LITTLE BIT.  Do not use the Best Gasket brand rear main seal, it leaks right away 

Here is my take on the Rear Main Seals:
It has been stated that doing the bearing cap mod ( what I will call Step A) and using the Rebuilders Choice Rear Seal (Step B) together will prevent the rear seal from leaking. 
So we have at least a couple of examples where if you do A + B = No Leaks.

This has always made me question what happens if you do the bearing Cap Mod (Step A) and use the Best Gasket (I will call Step C).   That is, does A + C = a leak? 

I just can't remember anyone doing the bearing mod AND installing the Best gasket and what the outcome was. I am not questioning that the Rebuilders Choice seal is not a "better seal" but I am wondering of the bearing cap mod take enough pressure off the seal to also stop leaks off the maybe inferior Best seal?

If we had a few, or at least a couple of people that have made the bearing cap mod and used the Best gasket and it still leaked, I think that would absolutely confirm that you do have the use the Rebuilders Choice seal even with the bearing cap mod.

As far as using other Best brand gaskets, I have used them off and on for 30 or 40 years and never remember any issues. 

So Jason, I thought the same thing that you questioned,

"... what happens if you do the bearing Cap Mod (Step A) and use the Best Gasket (I will call Step C).   That is, does A + C = a leak? "

 It's possible that my father, original owner of my 63, had the mod done back in the day. Who knows? I can't ask him because he is no longer with us.

 I wish I had nothing but time on my hands, if I did, I would give A + C a try. Unfortunately, I do not. So, I will use the gasket set I have from Best Gasket, repair the rest of my leaks, perform the modification and purchase a Rebuilders Choice rear main seal.

 Thank you everybody for your input! Much appreciated!

RSS

Photos

  • Add Photos
  • View All

Forum

Fan shroud and rear glass moldings for a 64 De Ville 4 windows sedan

Started by MARCELLO CASSANO in Wanted to Buy 11 hours ago. 0 Replies

Hi everyone from Miami, I recently bought a 1964 De Ville Sedan and I'm looking for a fan shroud for my 64. Any leads or help? Thank you!Continue

Dino Radiator Leak - Time to Recore!

Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 17 hours ago. 28 Replies

I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue

bulb for door handle 1963 Cadillac

Started by David Erickson in 1963/64 Cadillac Specific Discussion. Last reply by David Erickson 19 hours ago. 4 Replies

My lights in the side door panel are out on the driver and front passenger side of my 63.  The back lights work on the door side panelsDo you know where I might get bulbs and what I would reference…Continue

Body Plate for 63 Coupe de Ville with Bucket Seats and Power Vent Windows

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 2 Replies

When I get a chance I like to go back and clean up, and scan the body plates from the parts cars I have brought in. For the last few years I generally do that as I dismantle each car but early on I…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service