Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back up

Got it put back together, started up, and oil light turned off.. putting a hole in the gasket that the oil sump filter really helped out on that..

I only ran it for ab out 15 minutes. pulled out of my friends garage, and rode down the street,,

i noticed a knock or something tha wasnt there to start with,  I think its a leak at that driver side exhaust connection.  My reason for that is, when i pulled off the exhaust, the nut didnt come off, the hole screw came out of the block,, the nut was pretty much heat soldered on bolt,  So i dont think i was able to put the 33 pounds of torque on the connection as i was afraid of stripping out the threads on the block,,   so i got it as tight as i felt comfortable cranking down on it, but it didn't hit the 33 lbs.  

Can i get replacement screws at the part store for that??

What did i learn from all this,, hmmm,, really nice to have full car lift.  

lots to look at inside the engine, but since i didnt have to touch anything there, no problems.  

the guy at arizona parts in arizona, (the guy there was quite helpful)   told me to just soak the gasket until ready, i didn't know why, but did it for the second installation of the upper seal.. it went in very nicely with no friction until the last say 3/4 inch.  i found if i pushed the tail in, toward the shaft and pushed it would go on in.  No rubber came off the end as it did on the first installation so i assume it was flush on all edges and no problems.. 

i found out that to turn the crankshaft with plugs out,, put the big torque bar on the nut on the alternator, squeeze the belt, and turn,, crank shaft turnedmoved with no problem,, so I learned a new trick there...

i cant  say this was not easy, maybe due to my lack of experience, and fear of breaking something,, but, after about 2 weeks, i got it in.. the lift really made it easier,,

i havent noticed a leak yet, but it was a very short drive and warm up..will see tomorrow how it comes out.

It cost me three rear main seals.. first one i ruined, second one fit, and the third one was a back up if the second one went bad.  so thats about 120.   (40 a piece for best gaskets from Arizona vintage parts..

oil pan gaskets,, first one i had to remove because of my oil sump mistake and had to do again,, 22.0 a piece x 2   (44.00)

exhaust gaskets  i think the was about 20,0..   

brake cleaner, assembly grease, miscellaneous stuff about 50.00, so the out of pocket parts cost was probably 230 to 250.00.

 shop wanted 550 in labor,, i know if i used there labor rate, it was a 3000.00  labor repair,, but given the learning, the advice from everyone, i came out way better,, i will know for sure how it held tomorrow.  at least i know how to do it if i have to do it again,, God forbid...

again, thanks for all the help and patience...

Views: 1314

Reply to This

Replies to This Discussion

Kim, my gut feeling is still with the oil pan rear pan gasket. If I have understood everything correctly the additional oil leaking has been after you removed the oil pan and replaced the seal. It is hard to imagine a new seal would cause more leaking, but could see a rear pan gasket leaking if the gasket is not seated properly. You have done the best you can and would get the shop to install the oil pan and gasket. They have probably removed and installed dozens and have a lift. They should be able to properly install the oil pan, leave inspection cover off, drive it up on the lift and see where leak is coming from. If they cannot do this I would definitely look for another shop.

I will look into shop here n ms.  Guve him all details of past efforts, and cut him loose on pan.  Really does make a difference to get it on a lift ,   

I did more rootin under car defiiteley dripping strait out of the opening around the center alignment nipple.  May hv over smeared the rtv or left a chanell in there.

Oil loss.    60 miles =  1/2 qurat low

just got giggles, i cleaned off the guide nipple, and packed some silicone on that piece and the hole that it comes out of today,, its that 90 minute stuff, so gave it couple hours ro so to dry,   i was hopeful maybe it would block off the oil trail and that it was small and simple enough to go back up in to the pan, but not really thinking it would, but felt it was worth a try,

well, i did it and it stopped the leak from coming out of and down the nipple, it just pushed it back were it is coming out around the seal were the pan meets the bottom of the big round connection on the rear of the pan.. 

i dont know if that is good or bad or is helpful info to anyone, but thats what happened,  it just moved it back some,,still going to shop in next couple weeks.

How much oil are you putting in the car?  Max is 5 quarts, regardless of the dip stick marks.

4.5 qt. Pint of zinc additive.

RSS

Photos

  • Add Photos
  • View All

Forum

Cadillac Original Ads - 1964 Standard Ads

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 11 hours ago. 25 Replies

Just as I had done last December with the standard 1963 Cadillacs magazine ads, I have started scanning my 1964 Cadillac Ads, and will post here one by one, then combine into a single photo album and…Continue

Speedo Cable lubricant

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb Mar 12. 4 Replies

Eventually I’ll replace the speedo cable if needed but I believe the dash will need to come out to do that. However, shortly, I will be replacing the transmission on my 64 Fleetwood and I was…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon Mar 12. 1 Reply

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

Yaw bumpers

Started by Ron Perry in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge Mar 10. 11 Replies

I have sent 2 photos of the Transmission yaw bumpers (side mounts) It appears they only touch the trans bellhousing on the very edge. Is that the correct position? Does not seem right to me but I…Continue

Blog Posts

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Clock ‘64 DeVille

Posted by Matt Vander Hooven on July 23, 2023 at 7:36pm 2 Comments

Is there still a member in the Detroit area that refurbishes clocks?

Matt VH

Spark Plug Heat Range

Posted by Patrick Westphal on July 7, 2023 at 10:00am 1 Comment

I found a diagram that illustrates the main factor in determining a spark plug heat range that I was trying to describe to you during the chapter get together.

Here it is:

 

The main factor is the length of the ceramic insulator from the middle of the spark plug to the tip (where the spark happens)  

The insulator…

Continue

Events

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service