Turn signal arm removal and gear shifter arm
Looking for assistance in removing the turn signal arm from the turn signal assembly on a non-tilt steering column. Does it screw in there or do I need to take this little retainer off the top or ??? Thanks in advance.
Also, is there something that keeps the pin in place for the gear shifter arm or does the pin just need to be pushed out? I see a thin metal spacer between the top of the shifter and the pin, but I’m not sure if that’s holding the pin in there or not.
’63 Fleetwood Series 75
turn signal switch
shifter
Replies to This Discussion
-
Permalink Reply by Dennis P. DiBari on
-
Hi Brandon,
Check that steering column diagram I sent you last week (The one you had to Google). It has all the parts of the steering column listed from top to bottom. It's the one Jason posted.
Dennis DiBari
-
Permalink Reply by Brandon N. on
-
I did but it didn’t help much.
-
Permalink Reply by Russ Austin on
-
The turn signal arm screw out. There are 2 flat spots where a wrench will fit. The shift lever pin is pushed out. I use a small brass punch and a hammer. Yes, there is a shim plate, so get that as well when the arm comes out. Take not as to what side it is on.
Photos
Members
Forum
Finally got around to cleaning and re-lubricating the seat transmission. Now, it works flawlessly
Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 9 hours ago. 2 Replies 0 Likes
When I first got my 64 SDV about 8 years ago, the power seat made noise but didn't go anywhere. I promptly read up on it and proceeded to take the seat transmission out to clean and re-lubricate it.…Continue
Trivia # 35 - All About the Windshields
Started by Jason Edge in Trivia. Last reply by Logan Robb 22 hours ago. 4 Replies 0 Likes
Keeping the trivia "glass related":- How Many Different Windshields Were Used On All 1963 & 1964 Cadillac Body Styles? - What were the two main differences or subgroups of windshields? Hint, one…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by David Thomas on Saturday. 3 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
1963 & 1964 Equipment Percentages
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Saturday. 4 Replies 0 Likes
Here is a list of equipment percentages I had pulled from the Ward Automotive Yearbooks for 1963 and 1964 and have used for several trivia questions. I thought I would share the entire list as seen…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
© 2025 Created by Jason Edge.
Powered by
