I will add a link to the Help Page and fine tune this entry a bit later:
Within the same model year, the 62 Series and deVille Series fenders will be the same.
Within the same model year the Fleetwood 60 Special and Eldorado front fenders will be similar in overall shape, however you have different trim mounting holes for the side trim found on the 62 series and deVilles vs the wheel well, lower rocker and lower fender script found on the Fleetwood and Eldo. Of course holes can be filled in and new ones drilled so these fenders are easy to internchange.
Within the same model year the 75 Series and Commercial Chassis front fenders are the same however, they are very different from all other body styles due to the 1959 to 1965 center Fleetwood, and 59 to 64 Commercial Chassis center body sections they are adapted to. That is the shape at the rear is different.
The 63 & 64 Fenders are considerably different especially at the very front. First, a more subtle difference is the larger squared raised area near the side front for the wide side molding found on the 63's. The 64 side trim remained thin to the very front where it joined the thinner eyebrow molding.
The big difference is in the physical structure of the front of the fenders. the 64 had a large fender extension and headlight pan that bolted into the front of the fender, whereas the 63 had a have moon shape lower section the wide eyebrow trim attached to and a smaller headlight pan, that really wasn't an integral part of the fender like the 64 extension. Another main outward physical difference is going to be where they butt up nest to the upper grill. If you look at the illustrations of the front of the 63 vs the 64 you will see they are quite different, especially where they meet the fender. There are a few other subtle differences but these are the biggies.
See the 63 headlight and eyebrow pans:
See the very different 64 headlight pan and fender extension assembly:
I have attached a picture below of a 63 and 64 fender side by side.
Here are the 63 and 64 front Illustrations. Note the different shapes between the fenders, especially where they butt up next to the upper grill:
Tags:
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe 20 hours ago. 2 Replies 0 Likes
Is anyone here planning on going to the Back to the 50’s car show in Minnesota?
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 2 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth on Saturday. 15 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge Jun 11. 6 Replies 0 Likes
First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
June 22, 2025 from 8pm to 9:30pm – Zoom
0 Comments 1 LikeSwitch to the Mobile Optimized View
© 2025 Created by Jason Edge.
Powered by