Jason Engine Rebuild Project Pt 3 - Engine Complete

Jason Engine Rebuild Project Pt 3 - Engine Complete

Here are some pictures reloaded from the old site of my engine rebuild project. These pictures were taken May 6, 2012 after rebuild was complete and engine was ready to go in.

  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on September 15, 2012 at 8:41pm

The car was running fantastic today as we cruised down to the Clayton Harvest Festival Car Show and since I knew it might be a while before I can drive it as I replace the exhaust I changed out the metering rods to 4% richer for both cruise mode and power mode.   As good as it ran earlier now with the new richer metering rod jet configuration it is really running incredible.  I took it for one last spin before I start removing the custom dual exhaust and it is just really running great. It will be funny to hear it nice and quite when I get the new exhaust system installed, but couldn't help taking it out for one last blast before I start the change-out.  Just to back up a bit, when I had went from the ignitor II setup to the Ignitor III setup I returned the carb configuration to stock to get an ideal of  how the richer jets might improve with the III setup and it really makes a big difference!

Comment by Jason Edge on September 14, 2012 at 10:32pm

The engine now has 347 miles on it (162,278 on the car), and changes the oil for the first time since the rebuild.  I had planned to wait until 500 miles were on the engine but was anxious to change it now that I had least have some miles on it.  I'm running regular "on sale" 10W30 oil and wills switch to a semi-sythetic or all synthetic after 1000 miles are on the engine...which at my rate will be some time! :-)

Photos

  • Add Photos
  • View All

Forum

Back to the 50’s

Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe yesterday. 2 Replies

Is anyone here planning on going to the Back to the 50’s car show in Minnesota?

where to find 1963 Cadillac Plastic Door Pin Anchors

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 2 Replies

Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue

Rear Main Seal Oil Leak Fix with Bearing Cap Modification

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth on Saturday. 15 Replies

Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue

Future of CLC Judging

Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge Jun 11. 6 Replies

First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system.  The old system was very good, however, I believe what Bill and the…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service