I had sent Tri-City Plating a 64 rear center to see if it could be rechromed, and it was too far gone, but got into a conversation with Chip, and he said he has 4 good 1964 rear center cores. The rechrome price is $585 and claimed one for myself for my personal 64 CDV. That leaves 3 available, and I sent an email to the 3 contacts I had on my wait list looking for one. One has already indicated they found one, so that leaves at least 1 extra available... maybe 3 if the other 2 contacts do not want need or want one. I did ask about 63 rear centers, and Chip said they didn't have that one. I also told him to be on the look out for front lower end (buckets).
I have had other chrome work done by Tri-City and have been extremely pleased. If interested contact Tri-City at 1800-251-7536 and ask for Chip. Their website is at http://www.tricityplating.com/. Tell them Jason at Classic Cadillac Parts sent ya!
Tags:
I went ahead and made the call to order one. I had purchased a bumper recently that looked way better in the pictures. Thanks for the tip! Looking forward to getting the dented up bumper on my car replaced.
That's at least 2 of the 4 they have on hand spoken for.
Just spoke with Chip again today and apparently the rest of the bumpers were too rotted to be repaired, so I will be sending mine and hoping it is in good enough shape to restore.
Sounds good. Fingers crossed.
Started by Rob Spring in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies 0 Likes
Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata yesterday. 1 Reply 0 Likes
I meant to make this a priority over the winter and didn't get that far. I've tried to source all the parts individually, but that is a daunting task. Partly because I don't want to miss any…Continue
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari on Wednesday. 2 Replies 0 Likes
As they say, Better Late Than Never!I want to give a shout out to 63/64 Chapter Member Alan Grist, who brought his 64 Series 62 Four Window Sedan, to the 2025 CLC Winter Board Meeting in Chattanooga,…Continue
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by