I'm in need of a wiper motor for a 63 SDV. Mines toast, stopped at 90 degrees on the windshield, now blows fuse whenever power applied.
tbbahner@aol.com
Thanks
Tags:
Parts Geek got one $ 205 exchange , free shipping
Tom, do you have the shop manual? It has troubleshooting steps to identify the problem. Since it's blowing fuses its\'s either shorting to ground or just drawing too much load. My best guess would be to check the motor brushes, these cars are so old now,they may be worn out .Disassembly of this motor looks pretty involved though.. My parts car still has it mounted ,don't know how good it would be .
Good point on the brushes. I would recommend just having it professionally repaired. The piece will look and perform as new. This is a common GM wiper motor, so it is not a difficult motor to rebuild or repair. Just google windshield wiper motor repair.
Thanks all for the comments. I found one off a 64 on epay I'll try. Jason, you can take my name off you list for now.
While I've got this disassembled, I'm replacing all the washer hoses. Also looking to see if there's anything I can do to clean up the joints on the wiper linkage to reduce drag. Doesn't look like I can do much with it and still keep it dry(without lube). Any suggestions on this???
Remove the wiper transmissions and clean up the pivot heads that rotate. Use a penetrating oil to get the crud loosened up, and flush out with brake parts cleaner.
Removing the transmission can be time consuming, especially if you run in to issues getting any of those 9 Phillips Screws out that hold it in place. I would visually inspect, and unless you see major rusting, with the cowl chrome grills removed, hit the transmission assembly with compressed air and spray the pivot points with WD40 and work back and forth and you should be good to go for many years. If you have heavy rust and decay on the transmission assembly (which I have only seen occasionally) I have over a dozen excellent complete transmission assemblies for $50 each + s/h.
Hey all, thought I'd follow up on this thread.
Received the wiper motor off Epay and got it installed. We be "wipin" again!
Took the cowl grill assembly off and cleaned up all the joints on the transmission. Has much less drag than it did before. Still no washer but that's one of those things I'm not too worried about.
Thanks again to all for the assistance.
Tom B
Congrats! Yep, wiper is the main thing, You can pick at the washer as time permits. I had my car 15 years without a working washer and finally bought a repair kit and TCB'd it and sure felt good to see it work.
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 6 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson Feb 15. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2026 Created by Jason Edge.
Powered by