I'm in need of a wiper motor for a 63 SDV. Mines toast, stopped at 90 degrees on the windshield, now blows fuse whenever power applied.
tbbahner@aol.com
Thanks
Tags:
Parts Geek got one $ 205 exchange , free shipping
Tom, do you have the shop manual? It has troubleshooting steps to identify the problem. Since it's blowing fuses its\'s either shorting to ground or just drawing too much load. My best guess would be to check the motor brushes, these cars are so old now,they may be worn out .Disassembly of this motor looks pretty involved though.. My parts car still has it mounted ,don't know how good it would be .
Good point on the brushes. I would recommend just having it professionally repaired. The piece will look and perform as new. This is a common GM wiper motor, so it is not a difficult motor to rebuild or repair. Just google windshield wiper motor repair.
Thanks all for the comments. I found one off a 64 on epay I'll try. Jason, you can take my name off you list for now.
While I've got this disassembled, I'm replacing all the washer hoses. Also looking to see if there's anything I can do to clean up the joints on the wiper linkage to reduce drag. Doesn't look like I can do much with it and still keep it dry(without lube). Any suggestions on this???
Remove the wiper transmissions and clean up the pivot heads that rotate. Use a penetrating oil to get the crud loosened up, and flush out with brake parts cleaner.
Removing the transmission can be time consuming, especially if you run in to issues getting any of those 9 Phillips Screws out that hold it in place. I would visually inspect, and unless you see major rusting, with the cowl chrome grills removed, hit the transmission assembly with compressed air and spray the pivot points with WD40 and work back and forth and you should be good to go for many years. If you have heavy rust and decay on the transmission assembly (which I have only seen occasionally) I have over a dozen excellent complete transmission assemblies for $50 each + s/h.
Hey all, thought I'd follow up on this thread.
Received the wiper motor off Epay and got it installed. We be "wipin" again!
Took the cowl grill assembly off and cleaned up all the joints on the transmission. Has much less drag than it did before. Still no washer but that's one of those things I'm not too worried about.
Thanks again to all for the assistance.
Tom B
Congrats! Yep, wiper is the main thing, You can pick at the washer as time permits. I had my car 15 years without a working washer and finally bought a repair kit and TCB'd it and sure felt good to see it work.
Started by Bobby Brown in General Discussion. Last reply by Dennis P. DiBari 5 hours ago. 1 Reply 0 Likes
My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue
Started by Jason Edge in General Discussion. Last reply by Jason Edge yesterday. 4 Replies 0 Likes
So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies 0 Likes
I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by