Gentlemen,
In the last week or two, I've been noticing that when pulling up to stop light (low RPM) my headlights dim slightly, as do the instrument panel lights. I suspected that I should replace my voltage regulator, which I did today. 15 minute job. No big deal.
However, when I started the car, at idle, the GEN light came on and stayed on until I pressed on the accelerator just a bit and the GEN light went off, and stayed off as I drove the car.
As I approached a stop light, when the RMPs dropped off, the GEN light came on again. When the light changed and I started to accelerate, the GEN light went off. The cycle repeated itself.
So, because the wife doesn't know how look it takes to change the voltage regulator :-D, I drove over to the nearby auto parts store, bought a new alternator (I figured because why not..perhaps the old one was beginning to fail), and installed a new one.
When I started the car, the same thing with the GEN light continued: idle = GEN light. increasing the RPMs = NO GEN light. And, it appears the headlights at low RPM dim even more than before I changed the Voltage Regulator and the alternator. UGG!
I checked the ground on the voltage regulator and the ground appears to be solid.
The only thing I did not change in this circuit was what appears to be a variable resistor of some sort??? See below with the ARROW.
Any thoughts about what might be going on???? Could it be that the new voltage regulator I installed is bad?
Michael
Tags:
Here’s a video of the problem. Also, should ‘t the GEN light be on when the ignition key is in the ACC (eg radio only) position?https://youtube.com/shorts/8l7K_IuMIAA?feature=share
Thanks Mark. I’ll give it a shot.
I put the old voltage regulator back on and the GEN light has gone off and I’m no longer having the problem. Go figure.
i’m certain I need a new voltage regulator as the head lights are flickering and dimming slightly at low RPM.
I inspected the black ground wire from the alternator to the voltage regulator and it’s old and the plastic coating broken in several place. I was considering running a new ground wire and trying out the new voltage regulator again.
Of course, I could throw in the towel and take the car into my mechanic, but what’s the fun in that?
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 3 Replies 0 Likes
My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the…Continue
Started by Jason Edge in General Discussion. Last reply by Chris Codd yesterday. 1 Reply 0 Likes
Started by Jason Edge in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies 0 Likes
Here is the 4th picture in my collection of "Promo Pictures" - another 1963 Fleetwood 60 Special. This 60 Special appears to be Nevada Silver, Paint Code 14. …Continue
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Saturday. 2 Replies 1 Like
I had to replace the heater core in my 63 SDV, so I decided to replace all the dash lights with LED's. and replaced all the vacuum lines. While I was in there, I added a light to the headlight switch…Continue
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by