My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?
Tags:
Jason, are the wooden blocks a factory component? Mine also came with the black wood block for the tire block.
It is mega hot here this week. Perhaps repainting my bumper jack is something easy I can accomplish this week......
I believe all Cadillacs of the 60s and 70s came with those black-painted triangular blocks of pine. They did in my 67, 69, and 70 cars. I plan to take the dimensions off those and prepare a block for this 1964 car which is missing the block.
Did they come with one or two wedge blocks ?
One block in each of my cars - except the 64.
63's and 64's had one block.
Thatd be great! I think I have mine kicking around here somewhere. Let me know what the dimensions of yours is. I think mine was split in two it was so dry. Id like to remake mine as well.
Measurements of the block in the trunk of my 69 Cadillac:
Picture a right triangle:
Base = 3 1/2"
Height = 5 3/4"
Hypotenuse = 6 5/8"
The block is 3 1/2" thick, so if looking down on the base, you'd see a 3.5" square.
The block in my 67 Cadillac also is made of pine painted black, but the dimensions are a fraction of an inch different.
This is excellent! Thank you!
I shall remake mine as well
It looks great, but the animated picture is spectacular. The talent in this group is impressive.
Thanks for the picture. I will investigate.
Travis J. Hensley Online
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark 1 hour ago. 13 Replies 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion 4 hours ago. 0 Replies 0 Likes
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue
Started by Bobby Brown in General Discussion. Last reply by Logan Robb 9 hours ago. 2 Replies 0 Likes
My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue
Started by Jason Edge in General Discussion. Last reply by Jason Edge on Saturday. 4 Replies 0 Likes
So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by