Jason Edge's Discussions (4,210)

Discussions Replied To (3840) Replies Latest Activity

"You can send PayPal to jasonedge@nc.rr.com "

Jason Edge replied May 28 to Adjusting front camber

10 May 29
Reply by David Johnson

"I am not sure where you can get them new.. might try USA Parts, Kanter, Rock Auto. I…"

Jason Edge replied May 28 to Adjusting front camber

10 May 29
Reply by David Johnson

"Here is a visual of the camber eccentric ... the offset of the hole thru middle allo…"

Jason Edge replied May 28 to Adjusting front camber

10 May 29
Reply by David Johnson

"Gold Cadmium Plated Windshield Washer Screws - $2 Each I have the #10-14 hex hea…"

Jason Edge replied May 26 to Classic Cadillac Parts For Sale - Misc Items

245 Jun 1
Reply by Jason Edge

"A red white and blue floor standing basket was purchased on behalf of the 1963/64 Ca…"

Jason Edge replied May 25 to CLC Chapters VP Bob Crimmins & CLC SW Regions VP, Self-Starter Art Director Tim Coy Visit

3 May 25
Reply by Jason Edge

"You can usually tell if the rear driveshaft section is really good if those CV joint…"

Jason Edge replied May 25 to Anyone have a good driveshaft for a 63 Eldorado?

12 May 26
Reply by Louie Hernandez

"You can read the obituary for Bob Crimmins at this link: https://www.dayfuneralhome.…"

Jason Edge replied May 25 to CLC Chapters VP Bob Crimmins & CLC SW Regions VP, Self-Starter Art Director Tim Coy Visit

3 May 25
Reply by Jason Edge

"If Louie just needs the rear section they are  not that bad to ship especially UPS. …"

Jason Edge replied May 25 to Anyone have a good driveshaft for a 63 Eldorado?

12 May 26
Reply by Louie Hernandez

"Yesterday I learned the very sad news that the CLC Chapters VP Bob Crimmins (blue sh…"

Jason Edge replied May 24 to CLC Chapters VP Bob Crimmins & CLC SW Regions VP, Self-Starter Art Director Tim Coy Visit

3 May 25
Reply by Jason Edge

"I've had good luck with 0000 steel wool and WD 40. It is tedious and time-consuming…"

Jason Edge replied May 24 to Tips for cleaning and polishing the grill

2 May 24
Reply by Tosh Dickenson

RSS

Photos

  • Add Photos
  • View All

Forum

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 7 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 6 hours ago. 16 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

RPM at 70

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 13 hours ago. 1 Reply

I was questioning if my 63 was shifting into 4th , so I installed a tach and don't notice a 3-4 shift. Cruising at 70 the RPM is at 2600. Sounds high.  Has anyone noted RPM's at highway speeds?. I…Continue

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service