Carter AFB Idle Step Up Actuator
Recently, I was having some idle issues and found the vacuum at idle was very low. After testing everything I found the Idle Step Up Actuator had a leaking diaphragm. I contacted Daytona Parts to see if they had any, they didn't but said they could rebuild my actuator. I sent the actuator to them for the rebuild and was pleasantly surprised to receive it back looking like new. It looks great and holds vacuum with my MityVac. Hope it is pretty close to the proper adjustment when I get it installed.
Replies to This Discussion
-
Permalink Reply by 3ft7bqmb7dryo on
-
Looks fantastic.
-
Permalink Reply by David Thomas on
-
Thanks Russ. For many years I've read on the CLC board how good these folks are. This is my first experience doing business with them, I'm very pleased with the outcome and transaction.
After posting the pictures, I installed the actuator. After dialing in the adjustment, it works as well as it looks!
-
-
Wow! That's a used part? Very nice work. Mind if I ask how much for the rebuild?
-
-
Clovis, Yes, it is the original part to the car. Rebuild including the return shipping was $62. I'd say it's as close to new as you can get.
-
Permalink Reply by Jason Edge on
-
Looks like new yellow/gold zinc coating too? Probably almost worth the price for that alone!
-
-
-
I added Daytona Parts to our Parts Suppliers Page.
-
-
I'm going to check mine for leaks. Always good to get into that habit with our older cars.
Members
Forum
Dino Radiator Leak - Time to Recore!
Started by Jason Edge in General Discussion. Last reply by Bill Wolf 13 hours ago. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 2 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
64 Replacing dash illumination lights-how much has to come out to get to all of them?
Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies 0 Likes
Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue
Correct whitewalls
Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies 0 Likes
I just replaced my tires from Diamondback (I had bad results in the past from Coker). It was the second time, due to the age of the tires. About 18 years ago Diamondback made custom whitewalls…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
© 2025 Created by Jason Edge.
Powered by
