Anybody out there have any experience or direction how to remove and replace the chrome trim moulding around the front door window glass?    Kevin

Views: 683

Reply to This

Replies to This Discussion

Kevin, the window has t come out. If its a 63, lucky U.  2 screws hold the bar in place. The rollers on the regulator ride in the bar, on the bottom of the window channel

2 screws on the back of the top chrome L shaped piece, hold it to the channel.

I got it replaced.  Thanks Russ.  Kevin

Kevin, is your window already out of the car? If not follow shop manual to remove glass. Then remove screws that hold the side & top trim to the lower channel assembly and gently pry the trim away from glass. When reinstalling I have used a lot of WD 40 to get the window back wedged into the seal and trim and lower channel.

Thanks Jason.  It worked!!!!  Got it.  Kevin

so u have to take the front window out in order to remove front window trim??? im in process of trying to remove trim or trying figure it out .but dont wanna take that Big window out 

JBailey,

Looking at picture below for front window trim with read arrows pointing to  left and right roof panel trim, and green arrows pointing to 5 pc reveal trim:

--> left, top and right reveal trim next to glass (green arrows) - removes with reveal removal tool. (windshield does not have to be removed)

--> bottom left and right reveal trim behind cowl  (bottom green arrows) - cowl has tom come off to access 5/16" screws that hold lower reveal brackets in place. (windshield does not have to be removed)

--> left and right front roof panel trim (red arrows) - WINDSHIELD AS TO COME UP TO ACCESS TRIM SCREWS).  The removal of this trim indicating removal of windshield is in the Shop manual (page 16-80 in 1963 manual; page 16-85 1964 manual),  

Once you remove the windshield and rubber seal you will then have access to a series of screws that holds the left and right front roof panel trim in place as seen below:

RSS

Photos

  • Add Photos
  • View All

Forum

Christmas 2024 with the 1964 Fleetwood 60 Special

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies

A little late posting, but figured some may enjoy seeing it post holiday to keep the winter blues away!My wife, Annie, and I had a great time with the Fleetwood before the salt hit the roads here in…Continue

Anyone Ever Hear of or Use Gary's Steering Wheels

Started by Jason Edge in Restoration Discussion. Last reply by Chris Codd on Tuesday. 3 Replies

Scanning thru the Feb issues of Hemmings I found a listing for Gary's Steering Wheels. I didn't think I had heard of them but looked on our …Continue

Dino Diaries - Nov 19, 2024: Install Cad Plated Fender Skirt Brackets

Started by Jason Edge in General Discussion. Last reply by Jason Edge Jan 17. 6 Replies

Now that I am past the radiator project (and a couple of house projects), I can pick away at the my 64 Coupe de Ville Dino a bit.  Today I installed the left driver side cad plated fender skirt…Continue

Dino Diaries - All Jacked Up For Christmas!

Started by Jason Edge in General Discussion. Last reply by Logan Robb Jan 16. 4 Replies

I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue

Blog Posts

'63 Tailfin Tales

Posted by Mark Mata on January 14, 2025 at 12:06am 1 Comment

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service