Gentlemen,
I’m have a bit of a hard time removing the interior chrome windshield side moulding trim necessary to remove the dash pad. I’ve removed the screws, but the trim does not seem lose and I don’t want to force it. How do the chrome pieces actually lift out?

Views: 108

Reply to This

Replies to This Discussion

With bottom and top screw out, grab near the top and pull down and inward. After being installed 60 years the stick a bit, but with firm prying down and out, the inner A pillar ultimately will pop loose.

Thanks Jason.  I'll give that a try.

Also, I want to pull the black and plastic Radio Face Plate (see picture).  I've managed to get 5 of the 6 screws out, but one screw is impossible to see and is down near the ignition switch.  It appears it can only be reached with a small open end wrench, but I just can see it. (on of the reasons I am pulling the dash cover.   Any thoughts about getting that last screw out?   

Do you have have a nice chrome instrument bezel available?  My is okay, but it has some pitting dots.  Not horrible, but not clean either. 

Thanks, again.

Mike

On road til Jan 30. I can check for bezel when I get home.

Got them off!  Thanks, again!

RSS

Photos

  • Add Photos
  • View All

Forum

Fender Trim Removal

Started by Kevin Wray in Restoration Discussion. Last reply by Jason Edge yesterday. 6 Replies

Thanks to Jason's expert advice, I was able to remove the fender trim on my 63 de Ville without removing the fender. Pics contain the locations of the 3/8 in nuts and how to access them. My clips…Continue

Tags: removal, trim

Body side molding install help needed

Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies

I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue

ORIGINAL CAR

Started by David Erickson in General Discussion yesterday. 0 Replies

I have an all original 63 Cadillac Park Avenue.  It has won awards in the past in the Originality Category.  My question to the group is what types of work you can do on the car that does not cause…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service