63/64 Cadillac Website

Garage Photography & Other Shenanigans

When I am breaking a parts car down I will often do photo shoots of specific parts such as this 1964 429 Transmission to Engine Adaptor ring. Definitely not your typical super model photo shoot! Although.... that adaptor ring sure has some sexy curves! LOL

2 members like this

Facebook Facebook

▶ Reply to This

Replies to This Discussion

Permalink Reply by 3n49omug8n28i on February 5, 2016 at 10:52pm

Jason I am continually impressed by your dedication to your hobby. Cool shoot setup.

I can't wait for spring to get my car out of hibernation.

Looking at that adapter ring it's hard to believe that one could not be water jetted out of a solid piece of steel. This is what I did when I replaced my heat riser.

▶ Reply

Permalink Reply by Jason Edge on February 5, 2016 at 11:22pm

Someone bought an aftermarket adaptor ring and believe it was been posted here a year or two ago. It was solid aluminum as I recall.. a bit pricey... about double the $125 I will be asking for this one which is really nice. Here's one of the pictures I posted from the above "photo op!" LOL

▶ Reply

Permalink Reply by 2andfkilza2h0 on February 19, 2016 at 4:37pm

I just sold one with a complete transmission I had.

▶ Reply

RSS

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Members

View All

Forum

seat foam replacement

Started by Kevin Robles in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Robles 12 hours ago. 3 Replies 0 Likes

does anyone out there have any experience with seat foam replacement on a 63/64 Cadillac. I had my seats reupolstered many years ago in original leather/fabric and they still look great, but the…Continue

1963 carter afb carbureter stainless steel shim

Started by tim sparks in General Discussion 18 hours ago. 0 Replies 0 Likes

anybody have an xtra stainless steel shim for 1963 carter afb carb. thank youContinue

Timing cover corrosion

Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply 0 Likes

Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark yesterday. 13 Replies 0 Likes

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue