Hey all, the noise im lonking here comes and goes. Its not normally at startup, kind of shows after abput 10 minutes and most hearable at idle. Last i was hraering it when it was really hot out, but it went away. I believe the heat out was causing a vapor problem. I took car out in hi 80s for abput 40 minute ride, got to desination. Car never went over 1/3 on temp gauge, thought i was good, Got out, went in for about 2o min and car wouldnt start. Fuel in bowl was sbout an eighth high. Being 40 min from home, i panicked, got on internet searched vapor lock and found i could try and pour cold water on fuel pump, lines to try and drop temp. After about ten minutes of pouring on pump and lines, it started! Got home no prob. Outsode temp had dropped to 70s.
The "noise" had not been around for a week or two, then today, back again.
Rrason i explained above was for recent driving for reference.
Here is the noise. It was dark out when i took it, seems more toward back of engine. Any thoughts here
Thanks for listening
Tags:
Well i think i got it figured, it was pointed out the notch on the end of shaft not pointed in right dirction. So had to flip it back, reset the arms, and result was oil flowing up and out of top of rocker arm, down the spine, onto springs, the squuek was not present at all.
Thanks to all who helped me out. Learn something new everytime i fiddle w this thing
Congrats on the fix. I had assumed rocker arm shaft assemblies were installed correctly...especially after all the discussion we had prior about following the shop manual (in pariticular rocker arm installation on section 13.8, page 9-17 in shop manual) and the fact they had to be installed correctly. I pretty much always get things wrong when I assume these days. Not sure how many miles were on the engine with rocker arm shaft on backwards but hopefully no damage done. Regardless, fire it up and go enjoy a ride in the Caddy!
Started by Doug Scarrow in Wanted to Buy. Last reply by Dennis P. DiBari 5 hours ago. 3 Replies 0 Likes
for close to 20 years I have had a lovely Club Decal on my windshield now I wish to replace the windshield and would love to buy a decal if any one has one available See attached photosContinue
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe on Tuesday. 2 Replies 0 Likes
Is anyone here planning on going to the Back to the 50’s car show in Minnesota?
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 2 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth Jun 14. 15 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
June 22, 2025 from 8pm to 9:30pm – Zoom
0 Comments 1 Like
© 2025 Created by Jason Edge.
Powered by