does anyone out there have any experience with seat foam replacement on a 63/64 Cadillac. I had my seats reupolstered many years ago in original leather/fabric and they still look great, but the…Continue
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
Reply Deleted
This reply has been deleted. Return to the discussion.
Welcome to
63/64 Cadillac Website
Sign Up
or Sign In
Or sign in with:
Photos
Members
Ron
Dan Loukota
Travis J. Hensley Online
Preston Bealle
David
Thomas
Alan Clark
KEVIN P Kennedy
Xadrian
Jacob Foster
Rick Yasenchack
Erik LaValle
Forum
seat foam replacement
Started by Kevin Robles in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 2 hours ago. 1 Reply 0 Likes
does anyone out there have any experience with seat foam replacement on a 63/64 Cadillac. I had my seats reupolstered many years ago in original leather/fabric and they still look great, but the…Continue
1963 carter afb carbureter stainless steel shim
Started by tim sparks in General Discussion 3 hours ago. 0 Replies 0 Likes
anybody have an xtra stainless steel shim for 1963 carter afb carb. thank youContinue
Timing cover corrosion
Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 11 hours ago. 1 Reply 0 Likes
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue
Convertible bumper jack
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark 19 hours ago. 13 Replies 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
Continue'63 Tailfin Tales
Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments 0 Likes
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…

ContinueEvents
CLC & CLC Museum & Research Center National Events Through 2028
June 2, 2025 to May 1, 2026 – Across the USA!
1 Comment 0 LikesJuly 20, 2024 - 63/64 Cadillac Chapter Zoom Meet-Up
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 LikesCadillac Fall Festival and All-GM Car Show - Sept 26-27, 2025
September 26, 2025 to September 27, 2025 – Gilmore Car Museum
0 Comments 0 LikesCLC National Driving Tour 2025 - Cruisin The Capital
October 14, 2025 to October 18, 2025 – Albany & Lake George Area
1 Comment 0 Likes2026 CLC Winter Reunion & Board Meetings - Jan 7-10
January 7, 2026 to January 10, 2026 – Host Hotel: Element Orlando International Drive
0 Comments 0 LikesVideos
Guitars & Cadillacs
Added by Kurt 0 Comments 0 Likes
UFCU commercial
Added by Kurt 1 Comment 0 Likes
May 16, 2024 Finish honing with a Torque plate
Added by CHRIS CARLSON 0 Comments 0 Likes