After finding leak arpund rim of trans pan.  I ordered a gasket.  

I was checking to see if there are any pitfalls or suggestions to getting it right.

I assume drain pan from the drain bolt, then pull the pan and replace.  Will anything drop or fall from the underside of the pan on removal that i should be concerned with.

Views: 205

Reply to This

Replies to This Discussion

Kim, you probably have the pan well sealed. Look a little higher and you will probably find that your leak is from the dipstick tube O'ring seal. This is a common leak source. Clean and dry the area around the tube where it enters the transmission.  The tube must be square and straight to the case opening. After cleaning all oil off, dust some baby powder around the area where the oil is apearing, you'll be able to find the leak when it soaks the powder.

Another leak source is the oil cooler lines. There are two hoses connecting the spigots out of the transmission to the lines running to the radiator. Those sometimes do leak and can look like the pan is leaking when the oil runs down the transmission case.

Your description of the leak comming off the right front corner points more to the dipstick tube as the leak source.  HTH

Hi David,  yep, i already thoufht of that,  seema dry there.

Secondly,  after tapping and measuring for two hours, third gasket split at 10 lbs,    i know it was flat,  it was not warped,   thanfully i didnt load up anoth 35 doallrs of trans oi .  Wits, end,    gonna give it a rest for a day or so.

For reference,  used fel pro gaske .  Its a black oily looking dasket.   Im guessing cork, but has a black look.

Would doubling the gasket with an adhesive help the  pan to seal  a bit better and reduce a good deal of  the labor related to the trans pan change ? 

Who knows if the gaskets that are now available resemble  the stock original gaskets regarding thickness 

i do know that the gasket for the thermostat housing is half what they used to be stock 

I do double that gasket always myself 

just a silly example but could be a good part of the sealing issue you are having 

Hope you get it sealed this time but that would be my next move if the second gasket presents a problem 

Enjoy 

The gasket you have will tell the story, if you let it.  You need to take a very good look at it.  
If you split a gasket at 10 ft-lbs, then something isn't even.   Maybe someone hit the flange of the transmission with a scotchbrite wheel or a sander, and rounded it out.  Look at the way the edges of the gasket protrude after it's tightened.  Does it squeeze out only around the bolt holes or is it uniform?

You had a pan that seemed over tightened in the past.  Did you look to see if one of the bolt holes has a tiny crack from overtightening?     If you have a drain plug, drain the pan completely and let the transmission dry overnight, then the following day remove the pan and gasket.  The fluid will remain on the gasket in the exact location of the leak and the sealed portion will be dry.  You can then focus only at that point, looking for the cause.  

Sounds like a plan.  Will give it a go.  Put straitedge on case and see if its flat 

Thanks

The pan and gasket are supposed to be assembled dry without any sealer etc. If sealer is used, a torn gasket is usually the result. The sealer acts as a lubricant allowing the gasket to be squeezed out as the bolts are tightened. Tighten the bolts in a multi staged criss-cross pattern. HTH

This thread is turn out to be an exceptionally good education on installing a trans pan gasket correctly and of value to many who plan to do this repair at some point in the future 

Very nice repair support going on here !

Enjoy 

Sorr of an aside her .  I was buyin tran fluud yesterday, and got the castrol thatvwas gm and before 1983.  Inasked forvthe gallon siz .    She took to counter and chrged me a nickel.  Yes. 5 cents,   apparenetly castrol is reconfiguringvthe label so to dump stock at least atvcarques .   It was 5 cents for a gallon.  Yes a gallon, so if you need fluid,  and thats your brand,  and ur store has it,  id give it a try.    I bought 2,  saved 60.00 on firstvtwo debacles.     Just fyi

Kim 

This looks like the perfect time to be dealing with what the trans filter needs to be freshened up while you are in there already 

Cleaning or replacing the filter and fresh trans fluid is the way to get this done right for the long haul to protect the trans 

Enjoy 

Ok.  Is that a pull then plug back in operation, or more in olved, not sitting near my book.  I can order one if need be,  giving carvwork a day off tomoro

RSS

Photos

  • Add Photos
  • View All

Forum

Trunk won’t stay up!

Started by Don Savory in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 3 hours ago. 8 Replies

Anybody know what I need to do to make my trunk stay open. I got this car a few years back and it’s always been like this. I’m trying to everything in working order.

Engine and tranny seals

Started by Klutch in Restoration Discussion. Last reply by Tony and Ginny 429 5 hours ago. 55 Replies

Hey guys.Im going to be pulling my engine and tranny out soon. Theres some leaks on my engine and tranny. The main reason for this is because i need to paint the engine and engine bay. So i might as…Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 13 hours ago. 171 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 13 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 0 Comments

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service