Upper Control Arm Installation
I removed my upper control arms and replaced the bushings. I supported the lower control arms with jack stands. I reinstalled the upper control arms on the sub frame but now have about 2.5 inches between the spindle and the upper ball joint. I attempted to jack up the lower control arms to make up the gap but the car just went up instead of the control arms getting closer together so I could attached the upper ball joint. The engine is not in the car to add to weight which would help compress the springs.
Has anyone had this problem? What is a solution?
Replies to This Discussion
-
Permalink Reply by 3ft7bqmb7dryo on
-
ratchet strap
-
Permalink Reply by Robert Schles on
-
I tried the ratchet strap but as the spring compressed the strap got so tight it was impossible to move the ratchet.
I found using a 1/2" threaded rod through the shock tower work great. The rod goes in the same place as the shock with washers and a nut at the top. At the bottom, I placed a Kindorf channel strut across the lower control arm with washers and a nut. I tighten the top nut with an impact driver compressing the spring. The ball joint practically fell in place.
-
-
Thanks I give it a try
Photos
Members
Forum
They do exist!
Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion 6 hours ago. 0 Replies 0 Likes
An individual on Facebook was parting out a 1964 429 and transmission from a 70,000 MI sedan DeVille for an LS swap got lucky and scored this dent free oil cap before it hit the scrap iron pile with…Continue
Gear for power vent window
Started by James Barnes in Restoration Discussion. Last reply by Kurt on Thursday. 1 Reply 0 Likes
Im having a hard time locating the gear for the power vent window in my 64 Eldo. The existing one has 14 teeth and all I seem to be finding are ones with 17 teeth. Any suggestions?ThanksContinue
Rare Society of Automotive Engineers "The 1964 Cadillac Comfort Control" 1964 publication
Started by Jeff Tepper in 1963/64 Cadillac Specific Discussion on Sunday. 0 Replies 0 Likes
HI all,I found this publication on Ebay last year and bought it immediately. No one has told me that they have ever seen or heard of this publication.It was put out by the Society of Automotive…Continue
Check out Marlina & David Stone's 1964 Coupe de Ville in January Self-Starter
Started by Jason Edge in Chapter Discussion. Last reply by Mack Jan 25. 2 Replies 0 Likes
We have another 63/64 Chapter Member spotlighted in the January 2025 Self-Starter. In the "Letters to the Editor" section on page 6, you will see the picture below of Marlina & David Stone's…Continue
Blog Posts
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Vintage Air AC
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Events
-
February 16, 2024 - 63/64 Cadillac Chapter Zoom Meet-Up
February 16, 2025 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
Videos
© 2025 Created by Jason Edge.
Powered by
