Gentlemen,

In the last week or two, I've been noticing that when pulling up to stop light (low RPM) my headlights dim slightly, as do the instrument panel lights.   I suspected that I should replace my voltage regulator, which I did today.  15 minute job.  No big deal.

However, when I started the car, at idle, the GEN light came on and stayed on until I pressed on the accelerator just a bit and the GEN light went off, and stayed off as I drove the car.  

As I approached a stop light, when the RMPs dropped off, the GEN light came on again.  When the light changed and I started to accelerate, the GEN light went off.  The cycle repeated itself.

So, because the wife doesn't know how look it takes to change the voltage regulator :-D, I drove over to the nearby auto parts store, bought a new alternator (I figured because why not..perhaps the old one was beginning to fail), and installed a new one.

When I started the car, the same thing with the GEN light continued:  idle = GEN light.  increasing the RPMs = NO GEN light.    And, it appears the headlights at low RPM dim even more than before I changed the Voltage Regulator and the alternator.   UGG!

I checked the ground on the voltage regulator and the ground appears to be solid.

The only thing I did not change in this circuit was what appears to be a variable resistor of some sort??? See below with the ARROW.  

Any thoughts about what might be going on????  Could it be that the new voltage regulator I installed is bad?

Michael

Facebook Facebook

Views: 247

Reply to This

Replies to This Discussion

Here it is with the new voltage regulator.   As I consider (obsess) this problem, it seems to me it either has to be this, the ground, or a bad voltage regulator, no?

Here’s a video of the problem.  Also, should ‘t the GEN light be on when the ignition key is in the ACC (eg radio only) position?https://youtube.com/shorts/8l7K_IuMIAA?feature=share

Thanks Mark.   I’ll give it a shot.

I put the old voltage regulator back on and the GEN light has gone off and I’m no longer having the problem.  Go figure.

i’m certain I need a new voltage regulator as the head lights are flickering and dimming slightly at low RPM.

I inspected the black ground wire from the alternator to the voltage regulator and it’s old and the plastic coating broken in several place.  I was considering running a new ground wire and trying out the new voltage regulator again. 
Of course, I could throw in the towel and take the car into my mechanic, but what’s the fun in that?

RSS

Photos

  • Add Photos
  • View All

Forum

Replace Choke Tube or Install Electric Choke?

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by CHRIS CARLSON yesterday. 8 Replies

My mechanic has sourced a choke housing and new internals.  As you might expect, the choke tube is damaged and or clogged.  My options are to either replace the choke tube, or my mechanic recommends…Continue

Tags: Electric Choke, Choke Tube

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Buonaccorso yesterday. 10 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

window regulators

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Saturday. 2 Replies

For years my winds have seemed to be looser and less accurate than most modern windows.  I am thinking the soft parts are worn.  Has anybody gone through thier window regulators and felts to restore…Continue

Correct whitewalls

Started by Richard Stanley in 1963/64 Cadillac Specific Discussion on Thursday. 0 Replies

 I just replaced my tires from Diamondback (I had bad results in the past from Coker).  It was the second time, due to the age of the tires.  About 18 years ago Diamondback made custom whitewalls…Continue

Tags: width, whitewall, correct

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service