Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Views: 86


You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Robert on July 19, 2020 at 12:37pm

The trumpet was on the 63 Eldorado's cars. I got one off a 63 Eldo years ago and a friends 63 Eldo had one on it as well.

Comment by Tony and Ginny 429 on May 29, 2020 at 3:17pm

Hard to evaluate the parts condition  if covered in stuff 

A quick cleaning would improve buyers motivation that alone would make it a wise choice 


Comment by Ian Osborne on May 29, 2020 at 3:06pm

I agree completely on the cobwebs. If you're going to pick it up and photograph it, isn't that enough reason to wipe it down?

Comment by Jason Edge on May 29, 2020 at 1:16pm

I call it cobwebs! Patina is what you are left with when you brush off the dust, dirt and cobwebs! LOL

Comment by Robert Alan Shannon on May 29, 2020 at 1:02pm

Jason, I think that's what they call patina nowdays!

Comment by Jason Edge on May 29, 2020 at 12:44pm

Got to add, does it really take that much effort to run a wet rag across the horn and at least knock the cobwebs & dust off! At least they took some pictures of it. 

Comment by Jason Edge on May 29, 2020 at 12:41pm

Looks like the 64 short trump horn. Not used in 1963, but no reason you cannot add it. 
63 did have long trumpet horn - part # 199 9947  (Stamped 947 on rim of horn, B-Flat Note), that was standard on Eldorados and dealer installed option on other body styles. 

Comment by Robert Alan Shannon on May 29, 2020 at 12:20pm
Thank you Ian, I'm computer flunkie.
Comment by Ian Osborne on May 29, 2020 at 10:19am


I had seen it too. It's not the Holy Grail one or I would have bought it. Oh well, I'll keep searching.

Comment by Jason Edge on May 29, 2020 at 9:51am



  • Add Photos
  • View All


Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd yesterday. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 on Monday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment


 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 



Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…



Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?


  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service