Stuck power antenna
The mast on my power antenna is stuck up. I can hear the motor engage when I pull/push the knob, but no movement. The mast seems be rigid on the push wire or rod which wont move. Any thoughts about getting it unstuck?
Mike
Replies to This Discussion
-
Permalink Reply by Kurt on
-
I can't stand a conceited (stuck up) antenna. Sorry, couldn't resist : ). Anyway, do you hear a clicking sound when the antenna motor is running? There is a nylon cord that pushes/pulls the mast up & down. If the mast is simply stuck you will hear a clicking sound as the nylon cord grips and breaks loose trying the move the mast. In this case check the mast for any dents or bends that could be binding it. Also oil the mast with WD40 on steel wool. Try pushing the mast down manually while someone else pulls the knob. It can't be lowered unless the motor is winding up the nylon cord, If you don't hear a clicking the nylon cord or something else may be broken. In that case, you would need to remove the antenna and open it up to investigate. Do you have a shop manual? Instructions for removing the antenna are there.
-
Permalink Reply by Michael Vogler on
-
Thanks, Kurt. I have a shop manual and will get to reading!
-
Permalink Reply by 3ft7bqmb7dryo on
-
You can get a new antenna mast from CaddyDaddy.com I use them all the time.
Photos
Members
Forum
Burning Rubber
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Linda M. Brooks on Thursday. 5 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson on Sunday. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
