In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal.
I am wondering if anyone has replaced this seal OR found another way to seal the tube to the pan.
Many Thanks!
Logan
Tags:
Logan, FATSCO shows their part # is 4121-L according to their 1964- THM Catalog.
Here is a link --> FATSCO TH400 Catalog
From memory it just pushed in to the end of the cavity. I believe I matched mine up from my universal O ring kit I bought from Summit. It is posted on my transmission project thread.
Just fyi, the original part # was 531 917 in parts Group 4.133 and was a 1 year only item:
Are you talking about where the dip stick tube goes into the oil pan? That is a flare fitting and no seal goes there.
Yes correct. Where the tube goes into the pan. No seal there? Then what is this o ring I got from Fatsco????? I ordered one thinking that’s where it went but didn’t look right to me lol
Isn’t that the modulator port? I’m thinking now I am getting my wires crossed haha. Does the trans dipstick tube not mount INTO the pan?
I'm getting my words mixed tonight. There is an o-ring seal on the vacuum modulator port. I think Russ is right about where the trans dipstick filler tube attached to the transmission oil pan. I will check a couple of mine tomorrow ... am remember a compression fitting. There is also an O-ring seal on the speedometer gear.
Thanks! I appreciate the help. I got a new modulator and it came with an o ring, so we’re good there.
When I placed my Fatsco order, I ordered
2 pan gaskets
1 Filter ring
1 tube seal
front and rear seals
so there is an O ring somewhere HAHA!
I looked at my trans tube and there is a rubber seal up in the dipstick tube cap that twists onto the tube and it does look like it is something that can come out and be replaced but I have never thought about replacing it. you would think this would be part of the dipstick itself. Anyway, if it look like it would fit up on the dipstick cap that might be what they are referring to as the 1964 THM dipstick tube. Just guessing at this point.
I’d bet that is where the seal is intended for. I will check when home.
that being said, should there NOT be a seal where the tube attaches to the pan? Or is any sealant recommended there? Want to prevent as many drips as possible
Scott Santora Online
Started by Doug Scarrow in For Sale 11 hours ago. 0 Replies 0 Likes
Just listed. https://www.ebay.com/itm/266786607755Continue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 21 Replies 1 Like
Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket…Continue
Started by Doug Scarrow in For Sale on Thursday. 0 Replies 0 Likes
just listed solid 1963 1964 non tilt steering wheel. https://www.ebay.com/itm/266784089004$120 plus shippingContinue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 9 Replies 0 Likes
I have a 64 Cadillac Deville convertible. When the wiper switch is turned on the washer pump activates continuosly no mater what speed is selected. Washer pump shuts off when wiper switch shut off.…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by