Does anyone have a working ‘64 Convertible top switch like the one pictured below that you would be willing to sell, or have a lead on where I can get one? The new so-called “replacement” switch doesn’t fit the panel hole correctly nor the original mounting bracket. (And it looks different than the original! 😁).
Mike
Tags:
…or know of a place that can rebuild my switch?
Have you tested the switch with a continuity tester to confirm it is not working, and that your problem is not in wiring or elsewhere? These are pretty simple switches with contacts that bend down and make contact and close circuit when switch button is pushed one way or the other. Sometimes contacts just need to be cleaned or bent a little. Send it to me and would be glad to repair for free.. you would just pay for shipping it back.
Hi Jason,
Thank you for the reply and kind offer to repair my switch.
iThe problem is the switch, which I have been gingerly using for the past couple of years. With the dash restoration and having to remove the switch. When putting back in and testing on the circuit, it sparked and upon removal for inspection, a pin came out along with a small piece of the plastic casing. (I had one of the ugly 3 pin “reproduction” to test the circuit and it works just fine, except the new switch is hanging out of the hole; a temporary thing to get the top up and down). If you think with the broken pin it is still reparable, I will send it to you. Btw there is a broken clip on it.
Thank you again for your advice and repair offer.
Mike
I have the base and clips from other switches and should be able to repair yours. Let's say $10 for replacement parts. If interested in me repairing send to
Jason Edge
104 New Rand Rd
Garner, NC 27529
Note I will be shutting down around this Friday for my trip to Gettysburg and the GN so if I get it say by Wednesday I should be able to get it shipped out before I leave.
Thank you, Jason.
I’ll get it out to you tomorrow, overnight.
Mike
Good Morning, Jason,
I shipped the switch today by UPS 2nd day. You should receive it by Wednesday. Thank you, again.
Mike
Mike, The switch was received today and has been repaired. Check your email.
Jason.
You are amazing! Thank you.
Mike.
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin 2 hours ago. 1 Reply 0 Likes
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 5 hours ago. 2 Replies 0 Likes
As they say, Better Late Than Never!I want to give a shout out to 63/64 Chapter Member Alan Grist, who brought his 64 Series 62 Four Window Sedan, to the 2025 CLC Winter Board Meeting in Chattanooga,…Continue
Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 15 hours ago. 1 Reply 0 Likes
Hi all,Again I have issues with my AC system. Had it refilled recently but within a few days the system was empty again. The AC mechanic added tracer fluid to check for leaks, but there are no…Continue
Tags: 1963, core, evaporator, AC
Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion 16 hours ago. 0 Replies 0 Likes
I have a 1963 Series 62 convertible that I'm going to have the interior redone on. The car is Matador Red with a black interior. I'm looking to make the interior pop a little more than it does with…Continue
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by