‘64 Convertible top switch
Does anyone have a working ‘64 Convertible top switch like the one pictured below that you would be willing to sell, or have a lead on where I can get one? The new so-called “replacement” switch doesn’t fit the panel hole correctly nor the original mounting bracket. (And it looks different than the original! 😁).
Mike
Replies to This Discussion
-
Permalink Reply by Michael Vogler on
-
…or know of a place that can rebuild my switch?
-
Permalink Reply by Jason Edge on
-
Have you tested the switch with a continuity tester to confirm it is not working, and that your problem is not in wiring or elsewhere? These are pretty simple switches with contacts that bend down and make contact and close circuit when switch button is pushed one way or the other. Sometimes contacts just need to be cleaned or bent a little. Send it to me and would be glad to repair for free.. you would just pay for shipping it back.
-
-
Hi Jason,
Thank you for the reply and kind offer to repair my switch.
iThe problem is the switch, which I have been gingerly using for the past couple of years. With the dash restoration and having to remove the switch. When putting back in and testing on the circuit, it sparked and upon removal for inspection, a pin came out along with a small piece of the plastic casing. (I had one of the ugly 3 pin “reproduction” to test the circuit and it works just fine, except the new switch is hanging out of the hole; a temporary thing to get the top up and down). If you think with the broken pin it is still reparable, I will send it to you. Btw there is a broken clip on it.
Thank you again for your advice and repair offer.Mike
-
-
I have the base and clips from other switches and should be able to repair yours. Let's say $10 for replacement parts. If interested in me repairing send to
Jason Edge
104 New Rand Rd
Garner, NC 27529
Note I will be shutting down around this Friday for my trip to Gettysburg and the GN so if I get it say by Wednesday I should be able to get it shipped out before I leave.
-
-
Thank you, Jason.
I’ll get it out to you tomorrow, overnight.
Mike
-
-
Good Morning, Jason,
I shipped the switch today by UPS 2nd day. You should receive it by Wednesday. Thank you, again.
Mike
-
-
Mike, The switch was received today and has been repaired. Check your email.
Jason.
-
-
You are amazing! Thank you.
Mike.
Photos
Members
Forum
Clock Removal
Started by Jeff Donaldson in General Discussion. Last reply by Jason Edge 12 hours ago. 2 Replies 0 Likes
Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue
Dino Diaries - All Jacked Up For Christmas!
Started by Jason Edge in General Discussion yesterday. 0 Replies 0 Likes
I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue
Power Brake Booster
Started by Stephen Pechenik in General Discussion. Last reply by Bill Wolf yesterday. 13 Replies 0 Likes
Hello Co-Members,I recently purchased a low mileage1963 Sedan Deville Park Avenue. It is extremely solid and runs well. Neverthelss, it has minor problems that need to be addressed before I can…Continue
Body side molding install help needed
Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Wayne Morris on Saturday. 6 Replies 0 Likes
I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue
Blog Posts
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Vintage Air AC
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
accumulator dryer
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Events
Videos
© 2024 Created by Jason Edge.
Powered by
