When I purchased my 64 Fleetwood, one of the letters on the drivers side was missing, buy the time I drove it over 200 miles home, I had lost another letter. Now, almost a year later, I have an " EE WOOD " on the drivers side. 

I was lucky enough to find two full replacements (boy they were NOT cheap) that appear to be either NOS or a New Repop. Either way, they look GREAT! 

What is the best way to secure these back on to the fender? I believe from the factory, there were clips on the back side. Without removing the fender, I don't think I can re clip them back on. 

Suggestions on getting them back in there and to STAY PUT so I am not throwing money away?

As always, thanks for the help!

Logan

Facebook Facebook

Views: 95

Attachments:

Reply to This

Replies to This Discussion

I used superglue, and once it set up it was an extremely strong hold. Just be careful and don’t use too much. I first tried using 3m plastic trim adhesive, but it didn’t work well and a letter fell off (luckly in my driveway).
Interesting. Did you just put the super glue on the little pegs and push them in or did you put it on the backside of the letter?

Logan

On one side, I don’t have the holes since it’s a replacement fender from a non-fleetwood. So I ground off the pegs and just put glue on the backside of the letter. On the other side, I have the pegs so I used a little on the back of the letter and a little on the peg. Just be careful putting too much on the peg because if will get messy. 

RSS

Photos

  • Add Photos
  • View All

Forum

Logans Intake Project, 1964 Fleetwood, Progress Report #3

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 20 hours ago. 5 Replies

Not much of an Update and Questions: I was inspecting the top end and had removed the air cleaner in preparation to replace the intake. It was dirty so decided it needed a wipe down. My goof was…Continue

headlight / dimmer switch confusion (63 Sedan Deville)

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 4 Replies

The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue

Replacement Front Crankshaft Seal - 1964 Eldorado (429ci)

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 2 Replies

My mechanic is having difficulty sourcing a front crankshaft seal.  Can anyone recommend a replacement front crankshaft seal, and where to purchase?  Amazon has a few that I think(?) are replacements…Continue

Tags: Seal, Crankshaft, Front

Original Rim Color

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Stinson on Wednesday. 3 Replies

When I get some new shoes for my 64 Fleetwood, I'd like to recondition the rims. I'd thought of getting them powder coated, and still plan to eventually, but the $700 quote I received shunted that…Continue

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service